Hi,
My dreambox does not start anymore because of a wrong flash. I am getting only a green light and nothing else.
I tried to flash it using dreamup and other programs like (SUNRAY-FlashUP and Ferrarifiller) but it always stops at 'waiting for acknowledge'.
I managed to start the box using service connection (mini usb connection). And with putty (terminal connection) I can see all the commands and what is happening.
When bootin I am getting the following
At this moment my box does not start up, but when i push on the 'x' button on my laptop then it begins to start (magic)
and then I get the following on putty:
How can i flash after I started up the dreambox? now the dreambox is fully working and also the webinterface, ftp and network is working but i can't figure out where to flash the sim2 image. because dreamup still doesn't work
After I flashed it i will never flash anything to it
My dreambox does not start anymore because of a wrong flash. I am getting only a green light and nothing else.
I tried to flash it using dreamup and other programs like (SUNRAY-FlashUP and Ferrarifiller) but it always stops at 'waiting for acknowledge'.
I managed to start the box using service connection (mini usb connection). And with putty (terminal connection) I can see all the commands and what is happening.
When bootin I am getting the following
BCM74130011
012
K1
K2
K3
K4
K5
Shmoo Version=3.8
DDR Freq=0x0000018C
%00000001%
RC1=00000007
WC1=FFFFFFE6
RC2=00000018
WC2=00000021
RC3=0000000F
WC3=FFFFFFE6
RC4=0000000F
WC4=00000030
NWC=0000000B
RC5=00000007
WC5=0000000B
RC6=00000017
WC6=0000000B
NRC=0000000F
RW=00000011
WW=0000004B
G=00000000 R=0000000F W=0000000B
BL=00000000
RC1=00000003
RC2=00000015
BL=00000001
RC1=00000003
RC2=00000017
BL=00000002
RC1=00000004
RC2=00000016
BL=00000003
RC1=00000002
RC2=00000017
BL=00000004
RC1=00000005
RC2=00000017
BL=00000005
RC1=00000008
RC2=0000001F
BL=00000006
RC1=00000004
RC2=00000018
BL=00000007
RC1=00000007
RC2=0000001F
3
COPY CODE
COMPARE CODE
4567
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox DM500HD
FIRST STAGE 1.2/400 {BO23456}
2ND STAGE OK, build #83 (2011-03-01)
....
0.007 - BCM board setup
0.007 - fp init
0.007 - ca init
cannot read cert(2)
cannot read cert(2)
cannot read cert(2)
cannot read cert(2)
cannot read cert(2)
CA invalid
NO CONFIGURATION DATA PRESENT. STOP.
lcd: * ERR01: NO CA FOUND
At this moment my box does not start up, but when i push on the 'x' button on my laptop then it begins to start (magic)
and then I get the following on putty:
11.779 - load config
dCA: not existent, loading defaults
11.805 - config loaded.
* woke up from power
* pressto enter setup
lcd: BOOT #83
P23 detected!
- read config file: /boot/secondstage.conf
detected jffs2 blocksize: 16kb
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
++++++++++++++++++++++++++++UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
UUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUUU
dreamupd initialized
Scanning JFFS2 FS: . done.
find_inode failed for name=secondstage.conf
load: Failed to find inode
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /flash/bootlogo.elf
bootlogo size: 213186
### BCHP: unsupported revision: 7413B1
!!!Error BERR_INVALID_PARAMETER(0x2) at arch/800/magnum/basemodules/chp/7400/bchp_7400.c:308
BCHP_Open7401 failed!
lcd: /flash/vmlinux.gz
<5>Linux version 2.6.18-7.4-dm500hd (franz@franz-desktop) (gcc version 4.4.3 (GCC) ) #1 SMP Thu Jan 13 15:34:42 CET 2011
Fetching vars from bootloader... none present, using defaults.
Detected 256 MB on MEMC0 (strap 0x22bc0010)
<4>WARNING: read invalid MAC address ff:ff:ff:ff:ff:ff from flash @ 0xbffff824
Default command line =
root=/dev/mtdblock3 rootfstype=jffs2 rw console=ttyS0,115200
1 831ffeb8 83029418
g_board_RAM_size=256MB
Options: sata=1 enet=1 emac_1=1 no_mdio=0 docsis=0 ebi_war=0 pci=1 smp=1
CPU revision is: 0002a044
FPU revision is: 00130001
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
---> memsize from bootloader: 140
User-defined physical RAM map:
node [00000000, 08c00000: RAM]
node [08c00000, 07400000: RSVD]
<5>Reserving 116 MB upper memory starting at 08c00000
<7>On node 0 totalpages: 65536
<7> DMA zone: 65536 pages, LIFO batch:15
Built 1 zonelists. Total pages: 65536
<5>Kernel command line: root=/dev/mtdblock3 rootfstype=jffs2 rw console=ttyS0,115200
[4294667.296000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
[4294667.296000] Primary data cache 64kB, 4-way, linesize 64 bytes.
[4294667.296000] Synthesized TLB refill handler (23 instructions).
[4294667.296000] Synthesized TLB load handler fastpath (37 instructions).
[4294667.296000] Synthesized TLB store handler fastpath (37 instructions).
[4294667.296000] Synthesized TLB modify handler fastpath (36 instructions).
[4294667.296000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[4294667.296000] Found MIPS counter frequency: 203 Mhz
[4294667.296000] Using 202.501 MHz high precision timer.
[4294667.296000] Console: colour dummy device 80x25
[4294667.303000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[4294667.303000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[4294667.316000] Memory: 137216k/262144k available (2799k kernel code, 124804k reserved, 601k data, 136k init, 0k highmem)
[4294667.338000] Mount-cache hash table entries: 512
[4294667.339000] Checking for 'wait' instruction... available.
[4294667.339000] plat_prepare_cpus: ENABLING 2nd Thread...
[4294667.340000] TP0: prom_boot_secondary: Kick off 2nd CPU...
[4294667.342000] CPU revision is: 0002a044
[4294667.342000] FPU revision is: 00130001
[4294667.342000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
[4294667.342000] Primary data cache 64kB, 4-way, linesize 64 bytes.
[4294667.342000] Synthesized TLB refill handler (23 instructions).
[4294667.363000] Brought up 2 CPUs
[4294667.402000] migration_cost=1000
[4294667.404000] NET: Registered protocol family 16
[4294667.406000] registering PCI controller with io_map_base unset
[4294667.406000] registering PCI controller with io_map_base unset
[4294667.408000] SCSI subsystem initialized
[4294667.409000] usbcore: registered new driver usbfs
[4294667.409000] usbcore: registered new driver hub
[4294667.411000] NET: Registered protocol family 2
[4294667.424000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[4294667.425000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[4294667.426000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[4294667.427000] TCP: Hash tables configured (established 8192 bind 4096)
[4294667.428000] TCP reno registered
[4294667.428000] brcm-pm: disabling power to USB block
[4294667.429000] brcm-pm: disabling power to ENET block
[4294667.430000] brcm-pm: disabling power to SATA block
[4294667.433000] JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc.
[4294667.434000] Initializing Cryptographic API
[4294667.435000] io scheduler noop registered
[4294667.435000] io scheduler anticipatory registered
[4294667.436000] io scheduler deadline registered
[4294667.436000] io scheduler cfq registered (default)
[4294667.441000] Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
ÿ[4294667.442000] serial8250: ttyS0 at MMIO 0x0 (irq = 22) is a 16550A
[4294667.443000] serial8250: ttyS1 at MMIO 0x0 (irq = 67) is a 16550A
[4294667.444000] brcm-pm: enabling power to ENET block
[4294667.445000] Broadcom BCM7413 P21 Ethernet Network Device v2.0 Jan 13 2011 15:30:01
[4294667.447000] Config Internal PHY Through MDIO: 100 MB Full-Duplex (auto-neg)
[4294669.130000] brcm-pm: enabling power to SATA block
[4294669.147000] ata1: SATA max UDMA/133 cmd 0xB0510000 ctl 0xB0510020 bmdma 0xB0510030 irq 42
[4294669.148000] ata2: SATA max UDMA/133 cmd 0xB0510100 ctl 0xB0510120 bmdma 0xB0510130 irq 42
[4294669.149000] scsi0 : sata_svw
[4294669.453000] ata1: SATA link down (SStatus 4 SControl 300)
[4294669.485000] ATA: abnormal status 0x7F on port 0xb051001c
[4294669.485000] scsi1 : sata_svw
[4294669.789000] ata2: SATA link down (SStatus 4 SControl 300)
[4294669.821000] ATA: abnormal status 0x7F on port 0xb051011c
[4294669.821000] Broadcom STB NAND controller (BrcmNand Controller)
[4294669.822000] NAND_CS_NAND_XOR=00000000
[4294669.823000] brcmnand_probe: CS0: dev_id=ad76ad76
[4294669.823000] After: NandSelect=40000002, nandConfig=04042300
[4294669.824000] NAND Config: Reg=04042300, chipSize=64 MB, blockSize=16K, erase_shift=e
[4294669.825000] busWidth=1, pageSize=512B, page_shift=9, page_mask=000001ff
[4294669.826000] timing1 not adjusted: 5363444f
[4294669.826000] timing2 not adjusted: 00000fc6
[4294669.827000] BrcmNAND mfg ad 76 Hynix HY27US08121A (dream) 64MB
[4294669.828000]
[4294669.828000] Found NAND: ACC=00000010, cfg=04042300, flashId=ad76ad76, tim1=5363444f, tim2=00000fc6
[4294669.829000] BrcmNAND version = 0x0302 64MB @00000000
[4294669.830000] B4: NandSelect=40000002, nandConfig=04042300, chipSelect=-1
[4294669.830000] brcmnand_probe: CS-1: dev_id=ad76ad76
[4294669.831000] After: NandSelect=40000002, nandConfig=04042300
[4294669.832000] Found NAND chip on Chip Select -1, chipSize=64MB, usable size=64MB, base=0x
[4294669.833000] brcmnand_scan: B4 nand_select = 40000002
[4294669.833000] brcmnand_scan: After nand_select = 40000002
[4294669.834000] page_shift=9, bbt_erase_shift=14, chip_shift=26, phys_erase_shift=14
[4294669.835000] Brcm NAND controller version = 3.2 NAND flash size 64MB @1c000000
[4294669.836000] mtd->oobsize=16, mtd->eccOobSize=16
[4294669.836000] brcmnand_scan: mtd->oobsize=16
[4294669.837000] brcmnand_scan: oobavail=12, eccsize=512, writesize=512
[4294669.838000] brcmnand_scan, eccsize=512, writesize=512, eccsteps=1, ecclevel=15, eccbytes=3
[4294669.839000] brcmnand_default_bbt: bbt_td = bbt_main_descr
[4294669.841000] brcmnandCET: Status -> Deferred
[4294669.842000] numchips=1, size=4000000
[4294669.842000] Creating 4 MTD partitions on "bcm7xxx-nand.0":
[4294669.843000] 0x0000000000000000-0x0000000004000000 : "complete"
[4294669.847000] 0x0000000000000000-0x0000000000040000 : "loader"
[4294669.848000] 0x0000000000040000-0x0000000000400000 : "boot partition"
[4294669.849000] 0x0000000000400000-0x0000000004000000 : "root partition"
[4294669.853000] ehci_hcd_brcm_init: Initializing 2 EHCI controller(s)
[4294669.854000] brcm-pm: enabling power to USB block
[4294669.854000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-0)
[4294669.855000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
[4294669.856000] - USB h/w setup mode <B>
[4294669.856000] - USB power enable set for active LOW mode
[4294669.857000] brcm-ehci brcm-ehci.0: BRCM EHCI
[4294669.858000] brcm-ehci brcm-ehci.0: new USB bus registered, assigned bus number 1
[4294669.859000] brcm-ehci brcm-ehci.0: irq 62, io mem 0x10480300
[4294669.860000] brcm-ehci brcm-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
[4294669.861000] usb usb1: configuration #1 chosen from 1 choice
[4294669.862000] hub 1-0:1.0: USB hub found
[4294669.862000] hub 1-0:1.0: 2 ports detected
[4294669.964000] 10 Dec 2004 USB 2.0 'Enhanced' Host Controller (EHCI) Driver (EHCI-brcm-1)
[4294669.965000] drivers/usb/host/ehci-brcm.c: starting brcm EHCI USB Controller
[4294669.966000] brcm-ehci-1 brcm-ehci-1.1: BRCM EHCI
[4294669.966000] brcm-ehci-1 brcm-ehci-1.1: new USB bus registered, assigned bus number 2
[4294669.967000] brcm-ehci-1 brcm-ehci-1.1: irq 57, io mem 0x10480500
[4294669.968000] brcm-ehci-1 brcm-ehci-1.1: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
[4294669.969000] usb usb2: configuration #1 chosen from 1 choice
[4294669.970000] hub 2-0:1.0: USB hub found
[4294669.971000] hub 2-0:1.0: 2 ports detected
[4294670.072000] ohci_hcd_brcm_init: Initializing 2 OHCI controller(s)
[4294670.072000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-0)
[4294670.074000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294670.074000] - Resetting at b0480408
[4294670.075000] <-- brcm_start_hc
[4294670.075000] brcm-ohci-0 brcm-ohci-0.0: BRCM OHCI
[4294670.076000] brcm-ohci-0 brcm-ohci-0.0: new USB bus registered, assigned bus number 3
[4294670.077000] brcm-ohci-0 brcm-ohci-0.0: irq 63, io mem 0x10480400
[4294670.133000] usb usb3: configuration #1 chosen from 1 choice
[4294670.134000] hub 3-0:1.0: USB hub found
[4294670.134000] hub 3-0:1.0: 2 ports detected
[4294670.236000] 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (OHCI-brcm-1)
[4294670.237000] drivers/usb/host/ohci-brcm.c: starting brcm OHCI USB Controller
[4294670.238000] - Resetting at b0480608
[4294670.238000] <-- brcm_start_hc
[4294670.239000] brcm-ohci-1 brcm-ohci-1.1: BRCM OHCI
[4294670.239000] brcm-ohci-1 brcm-ohci-1.1: new USB bus registered, assigned bus number 4
[4294670.240000] brcm-ohci-1 brcm-ohci-1.1: irq 64, io mem 0x10480600
[4294670.296000] usb usb4: configuration #1 chosen from 1 choice
[4294670.297000] hub 4-0:1.0: USB hub found
[4294670.297000] hub 4-0:1.0: 2 ports detected
[4294670.399000] Initializing USB Mass Storage driver...
[4294670.399000] usbcore: registered new driver usb-storage
[4294670.400000] USB Mass Storage support registered.
[4294670.401000] i2c /dev entries driver
[4294670.401000] Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
[4294670.402000] ALSA device list:
[4294670.403000] No soundcards found.
[4294670.403000] TCP bic registered
[4294670.404000] NET: Registered protocol family 1
[4294670.404000] NET: Registered protocol family 17
... "IT doesn't end here"
How can i flash after I started up the dreambox? now the dreambox is fully working and also the webinterface, ftp and network is working but i can't figure out where to flash the sim2 image. because dreamup still doesn't work
After I flashed it i will never flash anything to it
