How to Use ShareMax

ig0r

Administrator
Messages
7,161
To use ShareMax, follow the following Steps:

1) Unzip the file on a Folder, you should have a SGBox sub-folder.
2) Configure your cwshare.cfg file and put into SGBox folder.
3) On Humax Receiver Set on Menu -- ToH -- Config
-- CAID Preselect to CARD+EMU+S or CARD+S+EMU
-- Card Blocker to ECM+EMM
-- Sharing Protocol to SSSP
4) Connect your PC to your STB with Null Modem Cable
5) Run ShareMax and Configure the Correct COM port.
6) Open the ports used in cwshare files IN/OUT in your Firewall.
7) First time you move to a Srambled Channel, a DOS windows will open(GBox) and connect to your CS...

Note:
=====
-- You cannot Share your CARD in Humax, it is only taking and cannot share your CARD with others at the moment.
-- Example of cwshare.cfg:
M: { xxxxx.dyndns.org { 123ABC45 }}
D: { yyyyy.dyndns.org { 1234 2345 { 456XYZ45 { 5 5 }}}}
I: { 09 }
X: { 30 }
N: { 00 01 03 00 4000 6000 }

xxxxx.dyndns.org your server and 123ABC45 is your password
yyyyy.dyndns.org Share Server, 1234 2345 ports used, 456XYZ45 Server password, 5 5 share level

You can repeat D: line for other Share Servers

Thanks paul_kh
 

Salah Said

HUMAX fan
Messages
163
I appreciate if you mention the error messages specially in newcamd servers
Please try to say it
Thanks a lot
 

ig0r

Administrator
Messages
7,161
Yes it true cupof
And write author post paul_kh

I am not tested this sw...

And good that you and Salah Said write here about this!

Then if this really bad SW i can delet this...

Please your opinions about it....
 

maikol

Registered
Messages
1
i usually have used this siftware....but what firmware is the best for usying sharing on himax 5400????
thank you
 

knightspeed

Registered
Messages
5
i have put all the current updates on my 5400z and i have Ran sharmax the way it says in the instuction but when i get to any channels that are scambled nothing happens on the computer or the box can some one tell me where im going wrong
 

knightspeed

Registered
Messages
5
Share Max

i have managed to get the sharemax to talk to the humax and it loads up the command console when i turn on the humax but it just stay on this image and does not do anything else even when on scambled channels
http://yfrog.com/3rsharemaxj
can enyone tell me what im supposed to do now
 

Salah Said

HUMAX fan
Messages
163
i have managed to get the sharemax to talk to the humax and it loads up the command console when i turn on the humax but it just stay on this image and does not do anything else even when on scambled channels
http://yfrog.com/3rsharemaxj
can enyone tell me what im supposed to do now

The Idea is simple
To do sharing you should have

1- A server includes the channels you want
2- A cable between computer and Humax
3- Internet connection all the times
4- Humax RAM is healthy (not all pages are zeros)
5- use a good PMCT Table which supports the channels
 

knightspeed

Registered
Messages
5
Thank you for the help i have just checked the Ram editor and they are indeed all zeros how do i go about changing them
 

knightspeed

Registered
Messages
5
Thank you again for all the help with this matter

i have managed to ket the new key.bin installed on the box but it still does not unlock any of the channels could you tell me if the card share part of 5.7 is supposed to do anything or if the program itself is to do anything when i go to a new channel i have added a newcanb server on that i have found but i am still not getting any thing.
sorry about all the questions but i would be greatful of any help that you can give me
 

mogembo

Registered
Messages
446
mate try to get new latest server details then u can see channels , free server not long lasting only for few minutes or hours
 

anubisz2

Registered
Messages
12
even if u have 5400 ... u will need to pay for the sharing service .... my advice forget about it useless
 
Top