juno driver 6.21

comaguser

Registered
Messages
1
Can somebody upload this driver

i like try cas studio 4,71 for fixing errors on magic module
thanks you would be very helpfull if you can manage a upload

my magic have delete errors in block 0 till 11

reprogramming wont work.

cam is in dreamload mode now as it was not longer recognized bij
receiver.
i have an oldfashion opentel 3000 receiver which still works
 

Petry

Registered
Messages
24
Cas Studio 4.7.1 For the driver: Driver needed Jungo is 6:22!
That was in 2004.
The repair of Magic module (if not a hardware failure was present)
darmals was inserted for the first time, software Cis 4.71. (Xilinx chip)

The Xilinx ("Magic Cas", "Matrix Cas") had to be described only new.
That is also today still as sharp with the new versions.

This time an ancient document to Cas Studio 4.71: From 2004
=================================================
Here is the solution!

Their brews the Cas Interface 2 (USB connection) and the program "Cas Interface Studio 4.7.1.
Next we need the files
"Matrix.cas + zBmr1170.bin" program for the Magic on matrix module,
or
"Magic.cas + and Penta 109.bin" Magic for normal module.

And now go go!

Magic module in the Cas Interface2 poke and connect with USB cable and connect to the PC.

Run the program "Cas Interface Studio 4.7.1 click" and then on the "Magic".
We then press the "Wizard" and the miracle can begin.
First, Let a (Select type of Cam) Magic for Magiccam, or matrix for Matrixcam (I have set matrix).
Then we load the Flash file for example "Mr1170.bin" and the Xilinx File "Matrix.cas. Now we press Next and then click Connect.
If the yellow-red spot to go to green, the program was not combined between Cam and manufactured.
Now we press Next again and then write, the program works. Now we wait until the message "Device programmed successfully" comes. Now press "ok" and remove Magic-module of Cas Interface2 and in turn on the receiver and wait until reinstecken.Receiver "Ci-module-initialization" ist.Siehe ended there, Magic-module is saved!
================================================== =======

With this solution, only the Xilinx chip is described as new.
________
Für Cas Studio 4.7.1 wird der Treiber : Jungo Driver 6.22 benötigt !!
Das war so im Jahr 2004.
Die Reparatur von Magic Modul (wenn kein Hardware-Fehler vorlag)
wurde darmals zum ersten mal eingefügt, Software Cis 4.71. (Xilinx-Chip)

Der Xilinx ("Magic Cas","Matrix Cas") musste nur neu beschrieben werden.
Das geht auch Heute noch genauso mit den neuen Cis-Versionen.

Hier mal eine alte Doku zu Cas Studio 4.71:Von 2004
=================================================
Hier ist die Lösung!!!

Ihr braut das Cas-Interface 2(USB-Anschluß) und das Programm "Cas Interface Studio 4.7.1".
Weiter brauchen wir die Dateien
" Matrix.cas+ z.B.mr1170.bin" für programmieren von Magic auf Matrix Modul,
oder
"Magic.cas+ und Penta 109.bin" für normales Magic-Modul.

Und nun gehst los!

Magic-Modul in das Cas Interface2 reinstecken und mit USB-Kabel verbinden und am PC anschließen.

Starte das Programm "Cas Interface Studio 4.7.1" und klicke dann auf das Symbol "Magic".
Anschließend drücken wir auf "Wizard" und das Wunder kann beginnen.
Als erstes Stellen wir ein (Select type of Cam) Magic für Magiccam,oder Matrix für Matrixcam (ich habe Matrix eingestellt).
Dann laden wir die Flash file z.B. "mr1170.bin" und die Xilinx File "Matrix.cas". Jetzt drücken wir auf Next und dann auf Connect .
Sollte der gelb-rote Punkt auf grün gehen,so wurde die Verbingung zwischen Cam und Programm hergestellt.
Nun drücken wir wieder auf Next und anschließend auf Write,das Programm arbeitet. Nun warten wir solange bis die Meldung "Device programmed succesfully" kommt. Jetzt drücken auf "ok" und Magic-Modul von Cas Interface2 entnehmen und in den Receiver reinstecken.Receiver einschalten und warten bis "Ci -Modul-initialisierung" beendet ist.Siehe da,Magic-Modul ist gerettet!!!
=========================================================

Mit dieser Lösung wird nur der Xilinx Chip neu beschrieben.
 
Top