Oscam-emu now supports powervu without streamrelay (on dreambox only...)

This problem is found only in new Dreambox models, with O.E 2.2/2.5(Dm520/525,820,7080,900). On older models OE 2.0(Dm 800se/800se V2, 7020, 500 HD) everything works perfect, from DES to CSA and back.
So,in my opinion,there is problem connected Dream OS/drivers for OE2.2/2.5.

Yes, you may be right.

Anything can be blamed on driver as a last resort.

Why don't we develop our own driver? Too difficult?

I believe the chipset is well documented unlike Qualcomm MSM 6500 chipset, anyway I developed my own drivers by reverse engineering the chipset in CDMA mobile phones.

dezider said:

to nie je problem oscamu, ale drivers v tom ktorom image.. kludne to posuvaj, nabuduce az bude nieco nove dostanete trt palov

This is not problem in oscam, this is problem in drivers .. in openatv and openpli ac3 sound work, all others images is only copy paste

Click to expand...

Hi,please pm your skype:thum:

Any news for VU+ ?

Hello Folks,

Please, are there any news for VU+ receivers? I would like to make PowerVU channels work on my VU+ Zero, Blackhole 3.03, Oscam 11390 but without stream relay (image freezes even if I tried several values for stream-delay in oscam.conf)

Is there any updated version of Oscam or Ncam that enables without stream relay on VU+ ? Or only Dreambox owners are the lucky ones ?

Thanks

no there is not, only with dm possible

thanks a lor for your reply :thum:

Rickk said:

no there is not, only with dm possible

Click to expand...

installing cccam on oscam for amiko 4a 4k combo

trying to install a sharing plugin to the hammmer 4k combo which has the same software as Amiko a4 4k combo using oscam new apk blue color

PLease help

my image on dm800hd pvr clone crash,and i do not have backup
now i install open pli 2.1 for ferrari sim and oscam 11209 emu patched but i forgotten config for power vu channels
Can somebody help me?I'm trying everything but i'm just getting it on log
rejected reader sid (142 ms) by SoftCam.Key (F/2/2/2) -

do someone can write complete config for dm800hd pvr clone open pli 2.1 for powervu

i didn't found similar post,so...
since yesterday (and new drivers release) and many vu+ models (solo se,zero,duo2,solo2 and all 4K models) support powervu decryption,without stream relay function...

georgeflu said:

i didn't found similar post,so...
since yesterday (and new drivers release) and many vu+ models (solo se,zero,duo2,solo2 and all 4K models) support powervu decryption,without stream relay function...

Click to expand...

Sound really good!!

Enviado desde mi SM-G925F mediante Tapatalk

I installed the new drivers, but channels of power 0.8w still no work until using stream.
My receiver is vu+ and drivers of 7/11/2018

disable stream relay, and change oscam dvbapi in =1 o.e 2.2
(you will find both in oscam web interface/config)

georgeflu said:

disable stream relay, and change oscam dvbapi in =1 o.e 2.2
(you will find both in oscam web interface/config)

Click to expand...

with duo2 (image openpli 6) where are the new drivers to download?

the drivers for the supported receivers are here http://www.sat-universe.com/showthread.php?t=170340&page=16

i don't know if openpli team (or any other team) has already added them
i just know that they are already installed in satdreamgr image...

Ferret said:

Here mate

http://www.sat-universe.com/showpost.php?p=2036840554&postcount=159

Back up your old drivers first just in case.

Click to expand...

I just installed now and my vu+ duo2 doesn´t start. I need enter the image again!

Regards!

Ferret said:

Just ftp in and change back to your old drivers your current image is too old to be compatible with latest drivers.

Click to expand...

But I can´t connect by FTP...

I´m using the last openVIX, Openvix 5.0.032 Release