AZ BOX PREMIUM PLUS IN BOOTING

G

gancio

Registered
Messages
24
ciao a tutti se qualcuno ha idea di questo risultato e cosa dovrei fare sarebbe il top



xosPe0 serial#cc6b68757c20a94d16aa028554b2c12d subid 0x50
xenv cs2 ok
xosPe0 serial#cc6b68757c20a94d16aa028554b2c12d subid 0x50
xenv cs2 ok
power supply: ok
dram0 ok (8)
dram1 ok (9)
zboot (0) ok
>
**************************************
* SMP863x zboot start ...
* Version: 2.4.0-2.8.0.1
* Started at 0x91000000.
* Configurations (chip revision: 6):
* Use 8KB DRAM as stack.
* Support XLoad format.
* Enabled BIST mode.
* Enabled memory test mode.
* Use internal memory for stage0/1.
**************************************
Boot from flash (0x48000000) mapped to 0x8c000000.
Found XENV block at 0x8c000000.
CPU clock frequency: 300.37MHz.
System clock frequency: 200.25MHz.
DRAM0 dunit_cfg/delay0_ctrl (0xf34111ba/0x000b7787).
DRAM1 dunit_cfg/delay0_ctrl (0xf34111ba/0x000a7787).
Using UART port 0 as console.
Board ID.: "852-E2"
Chip Revision: 0x8634:0x86 .. Matched.
Setting up H/W from XENV block at 0x8c000000.
Setting <SYSCLK avclk_mux> to 0x00000000.
Setting <SYSCLK hostclk_mux> to 0x00000100.
Setting <IRQ rise edge trigger lo> to 0xff28ca00.
Setting <IRQ fall edge trigger lo> to 0x0000c000.
Setting <IRQ rise edge trigger hi> to 0x0000009f.
Setting <IRQ fall edge trigger hi> to 0x00000000.
Setting <IRQ GPIO map> to 0x20090820.
Setting <PB default timing> to 0x10101010.
Setting <PB timing0> to 0x10101010.
Setting <PB Use timing0> to 0x000003f4.
Setting <PB timing1> to 0x00110101.
Setting <PB Use timing1> to 0x000003f3.
Setting <PB timing2> to 0x105f1010.
Setting <PB Use timing2> to 0x000003f8.
PB cs config: 0x000e0040 (use 0x000e0040)
Enabled Devices: 0x00021ace
BM/IDE PCIHost Ethernet I2CM I2CS USB PCIDev2 PCIDev3 SCARD
MAC: 00:02:14:18:61:17
PCI IRQ routing:
IDSEL 2: INTA(#14) INTB(#14) INTC(#14) INTD(#14)
IDSEL 3: INTA(#15) INTB(#15) INTC(#15) INTD(#15)
Smartcard pin assignments:
OFF pin = 0
5V pin = 1
CMD pin = 2
Setting up Clean Divider 2 to 96000000Hz.
Setting up Clean Divider 4 to 33333333Hz.
Setting up Clean Divider 5 to 25000000Hz.
Setting up Clean Divider 6 to 20000000Hz.
Setting up Clean Divider 7 to 20000000Hz.
GPIO dir/data = 0x76000038/0x76000000
UART0 GPIO mode/dir/data = 0x6e/0x00/0x00
UART1 GPIO mode/dir/data = 0x6e/0x00/0x00
XENV block processing completed.
Found existing memcfg: DRAM0(0x08000000), DRAM1(0x08000000)
Heap/Temp/Temp1/Dest start at 0x14000000/0x16000000/0x15000000/0x12000000.
Default boot index: 0
Scanning ROMFS image at 0x8c040000 (0x48040000) .. Found.
ROMFS found at 0x8c040000, Volume name = YAMON_XRPC
Found 1 file(s) to be processed in ROMFS.
Processing xrpc_xload_yamon_ES4_prod.bin (start: 0x8c040090, size: 0x0002fe84)
Checking zboot file signature .. Not found.
Trying xrpc_xload format .. OK
Checking zboot file signature at 0x13000000 .. OK
Decompressing to 0x91200000 .. OK (453328/0x6ead0).
Load time total 173/255 msec.
Execute final at 0x91200000 ..



**********************************
* YAMON ROM Monitor
* Revision 02.06-SIGMADESIGNS-01-2.8.0.1
**********************************
Memory: code: 0x11000000-0x11040000, 0x11200000-0x11204000
reserved data: 0x11240000-0x12440000, PCI memory: 0x12440000-0x12840000
Environment variable 'start' exists. After 1 seconds
it will be interpreted as a YAMON command and executed.
Press Ctrl-C (or do BREAK) to bypass this.

xrpc failed (9)--- if a xtask is using a cipher or if you reboot
--- xrpc will fail with RM_BUSY
Checking zboot signature.. it's not zboot file.
Error : Internal, code = ffffffff
YAMON> setxenv
(0x00) 4 a.avclk_mux 0x00000000
(0x00) 8 a.board_id "852-E2"
(0x00) 4 a.cd2_freq 0x05b8d800
(0x00) 4 a.cd4_freq 0x01fca055
(0x00) 4 a.cd5_freq 0x017d7840
(0x00) 4 a.cd6_freq 0x01312d00
(0x00) 4 a.cd7_freq 0x01312d00
(0x00) 4 a.chip_rev 0x86340086
(0x00) 4 a.enable_devices 0x00021ace
(0x00) 4 a.gpio_data 0x76000000
(0x00) 4 a.gpio_dir 0x76000038
(0x00) 4 a.gpio_irq_map 0x20090820
(0x00) 4 a.hostclk_mux 0x00000100
(0x00) 4 a.irq_fall_edge_hi 0x00000000
(0x00) 4 a.irq_fall_edge_lo 0x0000c000
(0x00) 4 a.irq_rise_edge_hi 0x0000009f
(0x00) 4 a.irq_rise_edge_lo 0xff28ca00
(0x00) 4 a.pb_cs_config 0x000e0040
(0x00) 4 a.pb_def_timing 0x10101010
(0x00) 4 a.pb_timing0 0x10101010
(0x00) 4 a.pb_timing1 0x00110101
(0x00) 4 a.pb_timing2 0x105f1010
(0x00) 4 a.pb_use_timing0 0x000003f4
(0x00) 4 a.pb_use_timing1 0x000003f3
(0x00) 4 a.pb_use_timing2 0x000003f8
(0x00) 4 a.pcidev1_irq_route 0x01010101
(0x00) 4 a.pcidev2_irq_route 0x01010101
(0x00) 4 a.pcidev3_irq_route 0x02020202
(0x00) 4 a.pcidev4_irq_route 0x02020202
(0x00) 4 a.scard_5v_pin 0x00000001
(0x00) 4 a.scard_cmd_pin 0x00000002
(0x00) 4 a.scard_off_pin 0x00000000
(0x00) 4 a.uart0_baudrate 0x0001c200
(0x00) 4 a.uart0_gpio_data 0x00000000
(0x00) 4 a.uart0_gpio_dir 0x00000000
(0x00) 4 a.uart0_gpio_mode 0x00007f6e
(0x00) 4 a.uart1_baudrate 0x00002580
(0x00) 4 a.uart1_gpio_data 0x00000000
(0x00) 4 a.uart1_gpio_dir 0x00000000
(0x00) 4 a.uart1_gpio_mode 0x00007f6e
(0x00) 4 a.uart_console_port 0x00000000
(0x00) 4 a.uart_used_ports 0x00000002
(0x00) 4 l.cs0_size 0x00000000
(0x00) 4 l.cs1_size 0x00000000
(0x00) 4 l.cs2_part1_offset 0x00000000
(0x00) 4 l.cs2_part1_size 0x00020000
(0x00) 4 l.cs2_part2_offset 0x00020000
(0x00) 4 l.cs2_part2_size 0x00020000
(0x00) 4 l.cs2_part3_offset 0x00040000
(0x00) 4 l.cs2_part3_size 0x00040000
(0x00) 4 l.cs2_part4_offset 0x00080000
(0x00) 4 l.cs2_part4_size 0x00680000
(0x00) 4 l.cs2_part5_offset 0x00700000
(0x00) 4 l.cs2_part5_size 0x00100000
(0x00) 4 l.cs2_parts 0x00000005
(0x00) 4 l.cs2_size 0x00800000
(0x00) 4 l.cs3_size 0x00000000
(0x00) 4 x.boot 0x00020000
(0x00) 4 x.csf 0x00000002
(0x00) 4 x.d0.cfg 0xf34111ba
(0x00) 4 x.d0.dl0 0x000a4444
(0x00) 4 x.d1.cfg 0xf34111ba
(0x00) 4 x.d1.dl0 0x000a4444
(0x00) 4 x.ds 0x00020080
(0x00) 4 x.dt 0x00000001
(0x00) 4 x.mux 0x00000701
(0x00) 3 y.startdelay "1"
(0x00) 4 z.boot0 0x00040000
(0x00) 4 z.boot1 0x00080000
(0x00) 4 z.boot2 0x00040000
(0x00) 4 z.boot3 0x00080000
(0x00) 16 a.build_date "TD210:20090123"
(0x00) 31 a.linux_cmd "mem=108m console=ttyS0,115200"
(0x00) 19 a.eth_mac "00.02.14.18.61.17"
(0x00) 40 y.start xrpc 0xac080090; load zbf 0xb3000000; go
(0x00) 4 x.p113 0x01020057
(0x00) 4 x.pll3 0x01020057
(0x00) 14 y.ipaddr "192.168.1.20"
(0x00) 15 y.subnetmask "255.255.255.0"
(0x00) 13 y.gateway "192.168.1.1"
80 records, 1722 bytes

YAMON> setxenv -b x.pll3 0x01020057
Original value: 0x01020057, New value: 0x01020057
Updating XENV block at 0x48000000.
.
XENV verification OK.
YAMON> setenv ipaddr 192.168.1.20
Updating XENV block at 0x48000000.
.
XENV verification OK.
YAMON> setenv subnetmask 255.255.255.0
Updating XENV block at 0x48000000.
.
XENV verification OK.
YAMON> setenv gateway 192.168.1.1
Updating XENV block at 0x48000000.
.
XENV verification OK.
YAMON> net init
Ethernet driver for EM86XX (v1.0)
(MAC 00:02:14:18:61:17, tx_desc/rx_desc = 16/32)

em86xx_eth:pen(em86xx_eth) - Full-duplex mode
em86xx_eth:pen(em86xx_eth) - 100 Mbit/s
em86xx_eth ethernet start
ipaddr: 192.168.1.20
subnetmask: 255.255.255.0
gateway: 192.168.1.1
YAMON> net up
em86xx_eth ethernet start
YAMON> ping 192.168.1.20
64 bytes ICMP-ECHO-REPLY user data received from 192.168.1.20
YAMON>

e qui che ho ridato ip al decoder ...dovrei inviare il karner nuovo ma nn riesco a collegarmi con filezzilla.....
Ne con altri tool... boo
a breve ci tiro una martellATA
 
You must log in or register to reply here.
Top