Motor Manuals Only - Please

satelliteman

Member
Messages
97
Installing a motorised satellite system..

Installing a motorised satellite system is a challenge but well worth the time spent. For this tutorial I will assume that you are going to wall mount your dish but if not you will be glad to know that most of the information here will still apply to you.

Following the instructions found here you should be able to have a fully working system within 3-4 hours.

You will need:

A satellite receiver
A satellite dish
An LNB
T & K brackets
A pole
A motor
Satellite cable
F plugs etc to make the connections
A satellite Meter
A compass
Ladder
Toolbox

Advice on what to buy

Determine what you want to watch i.e. movies, music, documentaries or whatever you can get as this will determine what satellite receiver you buy. Some receivers can be patched with software to allow you to view pay TV but others may require you to buy a conditional access module which you would have to program in order to view encrypted channels. There are receivers out there that use software to emulate these cam's but these types of boxes are usually for enthusiasts only and are quite expensive i.e. Dreambox.

Your best bet is to buy something that can be upgraded in the future but also very simple for you to use and for this purpose I would recommend a Technomate satellite receiver. The Technomate 1500 CI+ would be my choice as it represents good value and is so simple a young child could operate it.

Buying a complete kit is a good way of saving money and you know that everything you have purchased was designed to work together.

Satellite dishes can be thought of as very ugly devices but there are ways of disguising your dish. Metal dishes can be sprayed with car paint to help them blend into the surroundings or you may want to by a transparent satellite dish made of polycarbonates which for installations near the seaside are brilliant as they do not rust. New products are always being developed to help people disguise their satellite installations. As with allot of things size really does matter but due to the local council's dislike of satellite dishes you may not get planning permission for anything to large and your neighbours may complain if the dish obstructs a view from their property so I would recommend not going for a dish any bigger than 90cm though you can always risk a bigger dish and hope that nobody notices. Bigger dishes are essential for picking up weaker signals.

You want to buy a universal LNB and preferably 0.3db. The lower the number the better the picture quality will be. Universal means that the LNB is not fixed to only receiving channels on a certain band.

The motor should support Diseqc 1.2, Goto X and USALS as should your satellite receiver. USALS stand for Universal Satellite Automatic Locator System and use your longitude and latitude in order to track the satellites positioned above the Clarke belt. Having USALS will make things simple so it's a good thing to have. The Moteck Digipower 2100A would be my choice as it supports all of the above and can turn from 75E to 75W. This motor can be driven using buttons on the base of the unit which helps to set the dish up quickly. It also moves quite quickly so you don't have to wait so long when moving from one satellite to another.

Starting the install

A dry warm weekend is best for this preferably when your partner is out shopping or something. Start by looking for a neighbours Sky satellite dish and look where the dish arm is pointing. As we are in the North and the satellites circle the equator we know that our dish has to have a clear view of the south. Alternatively use a compass for a more precise reading. Look at your home and decide where the best place to mount the dish will be. Mine is on the side of my house just above the roof so it has an unobstructed view of the sky both East to West.

Once you have decided where the dish will go you need to fix the brackets to the wall. Opinions differ as to how these should be fitted to the wall but I prefer to have the K at the top as I believe it adds greater stability to the dish especially in high winds. The brackets should be approximately 1m apart. You will need strong bolts in order to get a good fixing.

Once complete you will need to attach the pole using U clamps and make sure that the pole is 100% vertical. This is the most important thing you will do so make sure it's spot on and check with either a spirit level or inclinometer.
A hammer may be needed to tap the brackets and pole in order to get things completely level.

Once complete go and have a cup of tea and read the instruction leaflet that came with your dish. Dish assembly is quite straight forward.

Unpack the motor and flick through the instructions. There should be a chart which tells you what to set the inclination and declination to on your motor and satellite dish based on your latitude. If you don't know what your latitude and longitude are you can visit www.multimap.com and type in your post code. Your latitude and longitude will be displayed under the picture of the map.

Now would be a good time to wire up the LNB to the motor. Pre made cables for this purpose are available.

Set the motor and dish to the settings given in the motor manual and triple check everything as it's far easier to work on the dish when it's on ground level. Now bolt the dish to the motor insuring that the motor is set to 0 degrees and that the dish goes on completely central. Again this is an important step so make sure it’s accurate.

Take the dish up the ladder and bolt it onto the pole making sure the dish will not be obstructed by anything. Using a compass find magnetic south and adjust to find true south. A map that shows the magnetic variation for your location is helpful but not essential as you can turn the dish manually and raise and lower the dish as long as the brackets are loosened.

As a general rule you want to find the closest satellite to your longitude, which will always be the highest satellite in the sky and gives you a better chance of tracking the arc, in my case I chose Thor 1W (If you were in Dublin say, you would be better with Atlantic Bird at 5W).

Plug in your satellite receiver and run a cable outside so that you can plug in your satellite meter. Satellite meters take power from the receiver so the receiver will need to be on and not just in standby. A good meter for this purpose is the Digisat Pro satellite meter. Connect your cable from the receiver and another cable to the motor and gently move the dish side to side and up and down until you get the best possible signal. Once complete you can tighten up the brackets and run a new satellite cable from the motor to the satellite receiver.

Satellite cables come in 3 main colours which are white, brown and black. You should use the colour of cable that is most pleasing to the eye. I find black cable is best suited to brick houses.

You should now weatherproof your hard work with silicone and tape and make sure that the cables are long enough that should the dish move a long way in one direction that the cables will not be stretched or damaged.

You can now set your receiver to USALS and start scanning and storing satellites.
It is advisable to check which satellites you can receive for your size / type of dish on the satellite forums. You may need to tweak your setup a little to get a good signal on all satellites.


That's all there is to it.
If you get stuck it may be advisable to seek professional help.
 

satelliteman

Member
Messages
97
installing using usals

For all that are still having problems

MOTORISED DISH USING USALS

1: Put up wall bracket on a south facing wall or as close to south as possible.
2: while motor is still on floor adjust your elevation/latitude markings on the motor to the same as your latitude where you live, if your motor markings have only elevation makings it is 90- latitude= elevation on motor. I use multimap.com to find my longitude and latitude. Tighten up as this will not have to adjusted again.
3: Attach your dish to motor while still on floor making sure the dish bracket is in line with the vertical line on the motor this is very important. Tighten up bracket as you should not have to adjust this again. And also half tighten up the nut on the elevation on dish.
4: Put dish and motor to wall bracket and point roughly south then loosely tighten up.
5: Run your cable from your receiver to the motor.
6: Input your latitude and longitude on your receiver before adjusting your dish, and then tell usals to go to Thor 0.8W/1W
7: Then adjust the dish for the best signal for Thor, By moving only the motor around the wall bracket/pole and the elevation on dish. I use a meter for this part but for people without a meter I believe a lot of people have been using BBC world to check the signal with. Once the signal is the best you can get it tighten everything up.
8: finish, hopefully
 

satelliteman

Member
Messages
97
A method of setting up a motor

1/ Bolt the motor to the mast/pole roughly aimed in the direction of your reference satellite,same for motor elevation as you may need to correct later,
2/ Fit the dish,Lnb,cable,receiver,
3/Drive the motor to Zero on your motor scale.
4/ Set up USALS for your area,& select your reference satellite the receiver,
5/ Fit meter between motor & reciever
6/ Now find the best signal for your reference satellite by adjusting the dish inclination & slacken off the motor mount mount now by looking at the meter achieve the strongest signal,
7/Now drive the motor to the extremes of your arc then by gently flexing the top & bottom of the dish see if the signal changes, if more signal when you flex the top of dish away from the Lnb means you need to adjust the motor elevation higher.
8/ If you move the motor elevation you will need to adjust your Dish Inclination at your reference satellite again,

I have found that this method gives perfect tracking of the Arc/Clarke Belt.
 

satelliteman

Member
Messages
97
complete motorised setup advice

1, have attatched the dish and motor to my ground stand, what direction MUST the dish be pointing to start with? what angle also?
2, once i have done that, do i just turn my receiver on and search for all satellites or is it not as simple as that? i have other peoples comments and got confused as some say it must be pointing directly south, and others say to have it pointing at thor 1w so it can sweep across the arc of satellites?
3, are there any other measurements i need to know longitude/latitude etc?
4, any advice?

-------------------------------------------------------------------------

The easy way if your putting it on a ground stand is.

1. Make sure the pole is 100% vertical take your time with this.

2. Set the elevation angle of the motor mount according to your location should be 52 deg and secure.

3. Mount the dish to the motor mount so it is roughly parallel and aim the whole lot due south.

4. Set your TM to usals and enter in Lat 52.5N Lon 1.1 east

5. Get an extension lead and take the stb and tv and set it up next to the dish so you can see it unless you have a sat meter.

6. Select SAT and select Thor, the dish should move slightly to the right.

7 Go to menu, advanced search, under sat make sure it says 1.0W Thor.

8. Arrow down to transponder and change it to 11.325

9. Move the the whole setup (not the pole) very slowly to the left or right so you are moving the motor around the pole with dish attached untill the quality bar improves, when it does peak the quality and slightly secure the position with the bolts.

10. Now move the dish up or down to improve the quality even more dont move the motor angle only the dish, you should get at least 75%, after you have tweaked it so you get a good quality signal tighten it all up and start scanning all the sats your install should be good.
__________________
 

satelliteman

Member
Messages
97
: Motor Manuals Only - Please

Fortec Star HH90 Motor User Guide

This is the user guide for the fortec star HH90 motor.
 

boisty

Banned
Messages
33
Alternatively use a compass for a more precise reading.

Found a brilliant site for aligning your dish correctly.

Dishpointer

Simply insert your location e.g. street name, zip code, country
Choose satellite i.e. Thor 1 degree west
Zoom in until you find your house (if it will allow) and move the marker to exactly where your dish will be positioned. It will then draw a line from where you intend to place your dish to the satellite. Simply look at the line and use a building etc in view to align your dish. I am going to use a garage just over the road as the line runs directly through the middle of it.

One tip though: Sometimes it will say address unavailable (for whatever reason I do not know), if this happens just use your town/city name and then manually find your street etc.
 
Last edited:
Top