Power of Dream HD+ 9000 Images

Status
Not open for further replies.

juli13

Staff member
Administrator
Messages
10,194
05/06/2011


We are pleased to offer you a POD for HD and et9000 et5000 Clarke-Tech / Xtrend. Because the manufacturer does not provide for the time cdk official image is based on OpenPlant. It is slightly different from a dream or vuplus POD HD, but it is a POD HD

Original image from 05/06

DOWNLOAD
 

tani1

Staff member
Super Moderator
Messages
17,767
Power of Dream HD+ Image for ET-9000

09-06-2011

Changes:

- Updated plugin Cooltv Guide by Coolman
- Updated Enigma2

rar.gif
podhd-et9000
 

tani1

Staff member
Super Moderator
Messages
17,767
Power of Dream HD+ Image for ET-9000

29-06-2011

Changes:

Update new drivers:

-increase framebuffer acceleration memory size
-always downmix audio on analog outputs
-support /proc/stb/fp/was_timer_wakeup (needs frontpanel update)
-vcr scart detection fix
-vfd improvements
-vfd: support greek and cyrillic charsets
-vfd: support additional symbols (see /proc/stb/lcd/*)
-pcm playback improvements
-sci improvements

rar.gif
podhd-et9000
 

tani1

Staff member
Super Moderator
Messages
17,767
POD HD - OpenPli 2.0 - ET9000

17-08-2011

Changes:

- Updated drivers
- Vfd: cyrillic / greek charactermap Improvements
- Scart: fix slowblanking
- Alsa: fix pcm playback of high bit rate data
- Fix mute status of ac3 passthrough mode in
- Add 'use_advanced_remote
- Add ioctl HDMI-CEC

Download ==> podhd-et9000
 

tani1

Staff member
Super Moderator
Messages
17,767
19.08.20111

New Image by SandBox Team based on Openpli 2.1

ATTENTION:
- It is not possible to go from 2.0 to 2.1 by an updated online, it is mandatory to flash a 2.1 full
- This new image requires an update of the bootloader before it can be installed

Download ==> podhd-2.1-et9000
 

juli13

Staff member
Administrator
Messages
10,194
27/08/2011

Code:
CAUTION: Changing the complete image management

Before: POD full image does not change when the updates, and install a demo with a POD to date, it falait load an image a little older and do the update

Now: the complete picture is updated POD also:

- To install a full POD: take the picture early in the thread, you are a day
- If you already have a good POD generation installed, ca does not change, just update it (Menu - Settings - Software Manager - Software update)
DOWNLOAD
 

juli13

Staff member
Administrator
Messages
10,194
Online update Power of Dream HD+ Image for ET9000 13/09/2011

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update
Code:
[B]Update of 13/09/2011
[/B]
- Update routine Enigma2/Openembedded
- Added in the DLC picons OpenPlant
 

juli13

Staff member
Administrator
Messages
10,194
Online update Power of Dream HD+ Image for ET9000 26/09/2011


Update drivers:


HDMI-CEC: address change signal with POLLPRI
sharpness-scaler: fixed 'neutral' value (middle of the scale)
-added video source viewport / clipping settings (/ proc / stb / VMPEG / [0-1] / clip_ *)

Update routine enigma2 ...

Note that sometimes the demo does not reboot itself at the end of the update, in this case to OFF / ON to interuptor

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update
 

juli13

Staff member
Administrator
Messages
10,194
Online update Power of Dream HD+ Image for ET9000 28/09/2011

et5000/et9000: Driver update

-tune speed improvements
-stc sync mode setting: /proc/stb/stc/[0,1]/sync
-dts audio ff/rewind/skip fix
-sci improvements
-timeshift detection (T/S vfd symbol)
-userspace timeshift symbol control (/proc/stb/lcd/symbol_timeshift, disables internal timeshift detection)
-fix pip with webbrowser combination

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update
 

juli13

Staff member
Administrator
Messages
10,194
Online update Power of Dream HD+ Image for ET9000 05/10/2011

- Modification of hypercam manager: the launch of enigmatic, verify that at least one local card is detected. If this is not the case, recovery hypercam. This should overcome the desire to hypercam etx000 on the launch.

- Changes introduced by OpenPlant etxx00 linux

-update routine Enigma2

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update
 

juli13

Staff member
Administrator
Messages
10,194
POD Image HD 2.1 ET9000 26/01/2012

Code:
[B]Updated from 26/01
[/B]
- Updated Card Manager version 2.17, fixes the concerns of the black screen updates this weekend.

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update
 

juli13

Staff member
Administrator
Messages
10,194
POD Image HD 2.1 ET9000 02/02/2012

Code:
[B]Update 02/02[/B]
 
- Update Manager map 2.18: support for HD channels on some maps csat.
- Provision in the DLC web interface OpenWeb: to install the current interface REMOVE BEFORE installing OpenWeb in plugins / extensions. Starting today PODHD the 'complete' automatically include OpenWeb instead of the old web interface after Dream.

To take the lastest update of POD Image just go to:

Menu - Settings - Software Manager - Software update
 

hilton

Registered
Messages
7,622
POD Image HD 2.1 ET9000 21/09/2012


Code:
- Update routine enigma
- Added BackupSuite Pedro Newbie in the DLC
- Added many Linux utilities in the DLC


To take the lastest update of POD Image just go to:[/code]

Menu - Settings - Software Manager - Software update
 

juli13

Staff member
Administrator
Messages
10,194
Power of Dreams HD + 3.0 Based on PLI

Code:
[B]Update of 30/06/2013




  Updates routine enigma and plugins
 

juli13

Staff member
Administrator
Messages
10,194
Power of Dreams HD+ 4.0 , goût OPli

Code:
We are pleased to introduce the new POD HD 4.0  28/08/2013

The upgrade from 3 to 4 can not be done online and requiers a flash image.
 Thank you for reading this post before installing

DOWNLOAD
 
Status
Not open for further replies.
Top