maistevale
Registered
- Messages
- 16
You can see the new DM 600
h**p://***.dream-multimedia-tv.de/english/products_dm600_technical.php
h**p://***.dream-multimedia-tv.de/english/products_dm600_technical.php
- 250 MHz PowerPC Processor (350 Mips)
- Linux Operating System
- 1 x Smartcard-Reader
- MPEG2 Hardware decoding
- Common available NIMs (DVB-S, DVB-C, DVB-T)
- V.24/RS232 Interface
- 10/100Mbit compatible Ethernet Interface
- 2 LED status
- 32 MByte Flash
- integrated IDE UDMA66 Interface
- Support for internal HDD 2,5" in any capacity
- unlimited channel lists for TV/Radio
- channel-change time < 1 second
- full automatic service scan
- supports directly bouquet-lists
- supports EPG (electronic program guide)
- supports own videotext
- supports multiple LNB-Switching control (DiSEqC)
- fully adaptable OSD in many languages and skin-support
- S/PDIF Interface for digital bit stream out (AC-3)
- 1 x Scart-interfaces
- S-Video connector
- analoge modem
DreamBox DM600 technical data
DBS-Tuner:
Frequency Range 950 …. 2150 MHz
Signal Level - 65 dBm …. - 25 dBm
Signal-to-Noise Level 12 dB max.
DBS-Tuner Input Connector F-Type female
Input Impedance 75 Ohm
AFC +/- 3 MHz
Demodulation Shaped QPSK
FEC Viterbi and Reed-Solomon
Viterbirate 1/2, 2/3, 3/4, 5/6, 7/8, automatic assimilation
Roll-off Factor 35 %
Demultiplexing according ISO 13818-1
Video decoder:
Video Compression MPEG-2 and MPEG-1 compatible
Video Standard PAL G/ 25 Hz
Video Formats 4:3 / 16:9
Footage 16:9, automatic assimilation for 16:9 TV-Device (over Scart)
Letterbox precolating for 4:3 TV-Device
Audio decoder:
Audiokompression MPEG-1 & MPEG-2 Layer I and II
Audio Mode Dual (main/sub), Stereo
Frequency: 32 kHz, 44.1 kHz, 48 kHz, 16 kHz, 22.05 kHz, 24 kHz
Output analog:
Output Level L/R 0,5 Vss on 600 Ohm
THD > 60 dB (1 kHz)
Crosstalk < -65 dB
Output digital:
Output Level 0,5 Vss on 75 Ohm
Sampled Data Filtering 32 kHz, 44.1 kHz, 48 kHz
S/PDIF-Output optical (AC3)
Video parameter:
Input Level FBAS 1 Vss +/- 0.3 dB on 75 Ohm
Teletext filter in conformity with ETS 300 472 Standard
TV-Scart:
Output: FBAS,RGB,S-Video
Serielle Interface RS 232:
Typ RS232 bidirectional
Bitrate 115,2 kBit/s max.
Plug Connector SUB-D-9
Function: Update of Firmware
Ethernet:
10/100 MBit compatible interface
Function: Update of Firmware, Connect to PC
UDMA66 IDE Interface:
Intern for connect 2,5" HDD
LNB Power and polarisation:
LNB Current 500mA max. ; short-circuit-proof
LNB Voltage vertical < 14V without load, > 11,5V at 400mA
LNB Voltage horizontal < 20V without load, > 17,3V at 400mA
LNB shut-off at Standby-Mode
Count of active satellite position:
DiSEqC 1.0/1.2 SAT POSITION / SAT OPTION
DiSEqC - Rotor Control
Power consumption:
< 15W / 12V
Input voltage:
DC12V,alternating acurrent +/- 15%
Extern power supply:
Input: 110-240V AC / 50-60Hz / 0,6A
Output: 12V = / 2,5A
Physical specification:
Ambient Temperature +15°C...+35°C
Humidity < 80%
Size (W x D x H): 195 mm x 130 mm x 40 mm
Weight: 0,6 kg
OE Build Configuration:
BB_VERSION = "1.6.6"
OE_REVISION = "96773728d3a1c1098153b43ed6f78da15656c899"
TARGET_ARCH = "powerpc"
TARGET_OS = "linux"
MACHINE = "dm600pvr"
DISTRO = "opendreambox"
DISTRO_VERSION = "1.4.0"
TARGET_FPU = "soft"
NOTE: build 200703241901: started
OE Build Configuration:
BB_VERSION = "1.6.6"
OE_REVISION = "299a5bba67fe8b549b69a516379c8da2651fedab"
TARGET_ARCH = "powerpc"
TARGET_OS = "linux"
MACHINE = "dm600pvr"
DISTRO = "opendreambox"
DISTRO_VERSION = "1.4.0"
TARGET_FPU = "soft"
NOTE: build 200703311243: started
OE Build Configuration:
BB_VERSION = "1.6.6"
OE_REVISION = "299a5bba67fe8b549b69a516379c8da2651fedab"
TARGET_ARCH = "powerpc"
TARGET_OS = "linux"
MACHINE = "dm600pvr"
DISTRO = "opendreambox"
DISTRO_VERSION = "1.4.0"
TARGET_FPU = "soft"
Dm600pvr Enigma2 TestImage of 080504
Friends,
New version of the TestImage with enigma2 rel 2.4 srcdate 080424.
New in Extra Setup:-
New Emumanager and Scriptmanager.
New Addonmanager - for ipkg download and install from user defined server, or from /tmp folder.
Removed some known bugs.
Also as before :-
Grab 0.70 (see screenshot tool below)
Webinterface
Recording and streaming improved (see below)
Yuv enabled
Picon
(1) Put the Enigma2 picon folder in '/media/cf/', or, '/media/usb/', or (2) make a new folder 'picon' with selected icons and put this folder in /usr/share/enigma2/
Extra Setup also includes :
New Emumanager :-
Enigma1 emus can be used. Ftp emu binaries to /usr/bin/cam and conf files to /etc or /usr/keys as necessary. Emu start and stop scripts to /usr/script/bin (see examples in image). Reboot, and any emu can be run or stopped from the Emumanager. The emu will continue in future bootups until stopped.
Also - view ecm.info.
New Scriptmanager :-
Ftp userscripts to /etc/scripts.
Crond :-
Edit by ftp the crontab file (in /etc) as usual with time and command etc. Start Crond from setup window and reboot. An example crontab is in the image which will create a folder cronresult in /etc. Crond will run after future reboots until stopped.
Inadyn :-
Edit the file inadyn.conf in /etc with your inadyn info e.g. usrname, password, alias. The example file is for the dyndns.org setup.
Telnet command > /usr/bin/inadyn --h for other options. Inadyn can be started and stopped from the setup window and will run after future reboots until stopped.
Also - view inadyn.log.
pmt.tmp :-
The image is set to include pmt.tmp in /tmp from start. If any emu start kills it, it can be restarted from the setup window. Check pmt.tmp window.
Skins :-
Default Skin - Nemesis.GlassLine .
Recording :-
Records as .ts files to hdd. Playback of .ts files with the 'video'button.
Streaming :-
Streaming (both viewing and recording on pc hdd) to pc is possible with TuxvisionE2.
Streaming of .ts, .mpg, dvd, divx and other file types from pc have been tested with Stream2dbE2 (Stream2dbE2).
Screenshot Tool :-
"Grab" included. Telnet command > /usr/bin/grab -f png for screenshot as .png and /usr/bin/grab -f bmp for screenshot as .bmp. Telnet command > /usr/bin/grab -h for help options.
Special thanks to :-
Tunhj1 and the CableLinuxInfo team for testing and suggestions, elektronikfreak for finding bugs, and other friends for suggestions and testing.
All log files can be found in /tmp.
No emus or keys included.
Have fun.
Regards, pcd.
Enigma2 of 080618
Cable patch
Harddrive options for recording and playback
- Insert pcip and share folder name in /etc/pcvideo
Caid and emuname in infobar
Plugins included
- Pauli-neutrino and Tuxcom
Skins included
-Nemesi.GlassLine and BlueLine.Black mod
Also as before :-
Grab 0.70 (see screenshot tool below)
Webinterface
Recording and streaming improved (see below)
Yuv enabled
Picon
(1) Put the Enigma2 picon folder in '/media/cf/', or, '/media/usb/', or (2) make a new folder 'picon' with selected icons and put this folder in /usr/share/enigma2/
Extra Setup also includes :
New Emumanager :-
Enigma1 emus can be used. Ftp emu binaries to /usr/bin/cam and conf files to /etc or /usr/keys as necessary. Emu start and stop scripts to /usr/script/cam (see examples in image). Reboot, and any emu can be run or stopped from the Emumanager. The emu will continue in future bootups until stopped.
Also - view ecm.info.
New Scriptmanager :-
Ftp userscripts to /etc/scripts.
Crond :-
Edit by ftp the crontab file (in /etc) as usual with time and command etc. Start Crond from setup window and reboot. An example crontab is in the image which will create a folder cronresult in /etc. Crond will run after future reboots until stopped.
Inadyn :-
Edit the file inadyn.conf in /etc with your inadyn info e.g. usrname, password, alias. The example file is for the dyndns.org setup.
Telnet command > /usr/bin/inadyn --h for other options. Inadyn can be started and stopped from the setup window and will run after future reboots until stopped.
Also - view inadyn.log.
pmt.tmp :-
The image is set to include pmt.tmp in /tmp from start. If any emu start kills it, it can be restarted from the setup window. Check pmt.tmp window.
Skins :-
Default Skin - Nemesis.GlassLine .
Recording :-
Records as .ts files to hdd. Playback of .ts files with the 'video'button.
Streaming :-
Streaming (both viewing and recording on pc hdd) to pc is possible with TuxvisionE2.
Streaming of .ts, .mpg, dvd, divx and other file types from pc have been tested with Stream2dbE2 (Stream2dbE2).
Screenshot Tool :-
"Grab" included. Telnet command > /usr/bin/grab -f png for screenshot as .png and /usr/bin/grab -f bmp for screenshot as .bmp. Telnet command > /usr/bin/grab -h for help options.
Special thanks to :-
Tunhj1 and the CableLinuxInfo team for testing and suggestions, elektronikfreak for finding bugs, and other friends for suggestions and testing.
All log files can be found in /tmp.
No emus or keys included.
Have fun.
Enigma2 of srcdate 080915
New addon download and install
Vlc video player patched for this image - play video, mp3, dvd etc
Userconfig and mount for cifs
Record and playback options for dreambox and pc hdd
Special shortcut : Button 0 -> Extra Setup
Download addons :
Button 0 -> Addonmanager -> Download addon -> Download updated panel -> select.
After install of Updated panel other items can be dowloaded.
Install addons :
Addonmanager -> Install addon -> select.
Before starting softcam first time Restart dreambox.
Also as before :-
Emumanager and Scriptmanager
Addonmanager
Webinterface
Recording and streaming improvedYuv enabled
Picon
(1) Put the Enigma2 picon folder in '/media/cf/', or, '/media/usb/', or (2) make a new folder 'picon' with selected icons and put this folder in /usr/share/enigma2/
Ftp userscripts to /etc/scripts.
Crond :-
Edit by ftp the crontab file (in /etc) as usual with time and command etc. Start Crond from setup window and reboot. An example crontab is in the image which will create a folder cronresult in /etc. Crond will run after future reboots until stopped.
Inadyn :-
Edit the file inadyn.conf in /etc with your inadyn info e.g. usrname, password, alias. The example file is for the dyndns.org setup.
Telnet command > /usr/bin/inadyn --h for other options. Inadyn can be started and stopped from the setup window and will run after future reboots until stopped.
Also - view inadyn.log.
pmt.tmp :-
The image is set to include pmt.tmp in /tmp from start. If any emu start kills it, it can be restarted from the setup window. Check pmt.tmp window.
Skins :-
Default Skin - Nemesis.GlassLine .
Streaming to pc:-
Streaming (both viewing and recording on pc hdd) to pc is possible with TuxvisionE2.
Special thanks to :-
Gutemine, Cassiopeia 2000, Hein Holz for advice and various patches, tunhj1 and LeoGR and for testing and suggestions, elektronikfreak for finding bugs, and other friends for suggestions and testing.
All log files can be found in /tmp.
No emus or keys included.
Regards, pcd.
New :-
Enigma2 of srcdate 081121
7 day epg from bskyb, skyitalia, nova gr, nrk, svt(viasat), tvprofil(rtl etc)
Mountmanager for cifs and nfs mount
Infobar date language options
Plugins YouTubePlayer and VlcplayerExtended included
New addon download manager
Special shortcut : Button 0 -> Extra Setup
7 day epg :
Based on plugin e2_loadepg. If a channel does not show epg, please edit the channellist.conf files in folder /usr/lib/enigma2/python/DF/e2_loadepg/dl_modules.
The format for a channel in the list is - id=n,channel name[,provider name] where :-
n=0 (channel NOT selected for epg); n=1 (selected)
channel name and provider name are the name of the channel and its provider in /usr/share/enigma2/lamedb. The provider name can be omitted if is same as the Default Provider at the top of the list. If no provider name in lamedb then use the word noprovider.
The epg days can be changed in the .conf files in the /dl_modules folder.
Download addons :
Button 0 -> Addonmanager -> Download addon -> Download updated panel -> select.
After install of Updated panel other items can be dowloaded.
Before starting softcam first time Restart dreambox.
Mount cifs and nfs:
First go to Button 0 -> extraSetup -> UserConf -> Edit command -> Press OK and edit command.
Next time you select Video button (for playback) or Red button (for recording) you get a choice for dreambox hdd or cifs or nfs hdd.
Also as before :-
Emumanager and Scriptmanager
Addonmanager
Webinterface
Recording and streaming improvedYuv enabled
Picon
(1) Put the Enigma2 picon folder in '/media/cf/', or, '/media/usb/', or (2) make a new folder 'picon' with selected icons and put this folder in /usr/share/enigma2/
ftp userscripts to /etc/scripts.
Crond :-
Edit by ftp the crontab file (in /etc) as usual with time and command etc. Start Crond from setup window and reboot. An example crontab is in the image which will create a folder cronresult in /etc. Crond will run after future reboots until stopped.
Inadyn :-
Edit the file inadyn.conf in /etc with your inadyn info e.g. usrname, password, alias. The example file is for the dyndns.org setup.
Telnet command > /usr/bin/inadyn --h for other options. Inadyn can be started and stopped from the setup window and will run after future reboots until stopped.
Also - view inadyn.log.
pmt.tmp :-
The image is set to include pmt.tmp in /tmp from start. If any emu start kills it, it can be restarted from the setup window. Check pmt.tmp window.
Skins :-
Default Skin - Nemesis.GlassLine .
Streaming to pc:-
Streaming (both viewing and recording on pc hdd) to pc is possible with TuxvisionE2.
Special thanks to :-
Gutemine, Cassiopeia 2000, Hein Holz for advice and various patches, tunhj1 and LeoGR and other friends for testing and suggestions, and of course elektronikfreak for finding bugs.
All log files can be found in /tmp.
No emus or keys included.
Regards, pcd.