Technomate HD Tutorials

tani1

Staff member
Super Moderator
Messages
17,767
How to download by USB to TM-800 HD

1 -DO NOT MAKE FOLDER IN THE USB THEN INSERT USB TO THE FRONT USB INPUT
2 -TURN ON TM-800 FROM REAR.
3 -SEE MINI ROOT THEN IMMEDIATELY PERES STANDBY FOR 2 SECONDS
4 -SEE IP ADDRESS THEN PRESS MENU ,,IT WILL START DOWNLOADING
5 -AFTER DOWNLOAD FINISHED DO FACTORY RESET,
 

elgeneral

Registered
Messages
7,811
Sharing TM HD


Server Settings


1st Turn on the
2nd Go to settings network adapter
* Main menu -> Setup -> System -> Network -> Adapter settings

95064869.png


3. Wyłacz ‘Use DHCP’
4. Change the 4th part of the IP address (NEVER CHANGE THE OTHER 3 PARTS OF THE IP ADDRESS)
For example: 192.168.1.159 (with DHCP On) -> 192.168.1.211 (with DHCP Off)
5. Wyłącz i włacz odbiornik ponownie
6. The message "STARTING..." will appear on the front panel
7. Press the OK button a few times on the front panel until the message "Checking Key" appears
8. Check the IP Address
*In this example, it is 192.168.1.211
9. Open the web browser in your computer (Internet Explorer, etc)
10. Enter the IP Address (from step 8) in the web browser (in the white box where you enter a website address). The following will appear (*If you can’t see a static IP, you will need to upgrade to the latest version):

34718459.png


11. Click on CCcam Edit and then you will see this:

66821882.png


12. In ‘Add Line at the bottom...’ type “SERVER LISTEN PORT : 45000” in the white box and then click on Add Line
*You can change the Port value from 20000 ~ 60000 (recommended)

13. Click on Previous Page

43360560.png


14. Type “F: Id password 0 0 0” in the white box and then click on Add Line
* It needs a temporary ID & Password for the Slave. For the ID & Password use only letters (a,c,B,N…..) & numbers (1,2,3….) but not any special characters (!,@,#,$......)
For example, if the ID is user1 and password is pass1 :

F: user1 pass1 0 0

15. Click on Previous Page
16. If you have 2 or more slaves, repeat steps 14 & 15, for example, if there are 3 slaves:

F: user1 pass1 0 0 0
F: user2 pass2 0 0 0
F: user3 pass3 0 0 0

17. Turn the Power Off and On
18. Set/Link the port between the Router and the receiver
*Check the router’s manual for Port forwarding
*Search ‘Port Forwarding and your Router’s model’ in Google, for example: ‘bt 2700hgv port forwarding’

Code:
[B]For example[/B]:
http://portforward.com/english/routers/port_forwarding/BT/BT2700HGV/Echolink.htm
]http://portforward.com/english/routers/port_forwarding/TP-Link/TL-R460/Echolink.htm
http://portforward.com/english/routers/port_forwarding/Huawei/EchoLife-HG520s/Echolink.htm
http://portforward.com/english/routers/port_forwarding/Netgear/DG834G/eMule.htm
http://portforward.com/english/routers/port_forwarding/Philips/SNA6500/Echolink.htm
http://portforward.com/english/routers/port_forwarding/Linksys/WRT54G/


Client Settings

1. Turn ON the receiver
2. The message "STARTING..." will appear on the front panel
3. Press the OK button a few times on the front panel until the message "Checking Key" appears
4. Check the IP Address
5. Open the web browser in your computer (Internet Explorer, etc)
6. Enter the IP Address (from step 4) in the web browser (in the white box where you enter a website address). The following will appear (*If you can’t see a static IP, you will need to upgrade to the latest version):

34718459.png


7. Click on CCcam Edit, and then you will see this:

66821882.png


8. In ‘Add Line at the bottom...’ type “C: Master’s static IP 45000 user1 pass1” in the white box and then click on Add Line, for example:

* Check the Master’s Static IP in step 10 of <Master setting>
* If the Master’s static IP is 211.144.178.211 and the Slave is No 3, therefore you should type:
C: 211.144.178.211 45000 user3 pass3
* You should check the Master’s SERVER LISTEN PORT (see Step 12 of <Master setting>)
If the Listen Port is 35000, type as follows:

C: 211.144.178.211 35000 user1 pass1

9. Click on Previous Page
10. Turn the Power Off and On


Mil gracias a Dios
 

tani1

Staff member
Super Moderator
Messages
17,767
How to download by USB to TM-800 HD Linux

1-Save tm-800 image in USB do not use folder re name like this ****> TM800_update.bin .
2-Turn on from rear
3-As soon as you see starting press stand by button once see mini root and wait
4-Wait until you See box ip then press menu button . It will take about 2 minutes see success then take USB out. wait for re boot
 

tani1

Staff member
Super Moderator
Messages
17,767
HOW TO DOWNLOAD IMAGE BY MINI WEBTO TM-800 HD

1-TURN ON TM-800 FROM REAR.
2-PRESS INTERMITTENTLY ON STAND BY BUTTON
2-SEE MINI ROOT THEN
3-SEE box ip example 192.168.1.?? <<< Last digit should be anything from 1 to 999
4-Go to internet explorer type example 192.168.1.???,
5-See mini web go to browser select your image press download
 

elgeneral

Registered
Messages
7,811
[ame="http://www.youtube.com/watch?v=2yupgb1GTY8"]YouTube- TM800HD flashing and setup wizard[/ame]
 

elgeneral

Registered
Messages
7,811
How to change the password in TM 800 Hd of the remote control

After factory reset using image or after 15-07-2010
to download new image use LAN + BLUE BUTTON
Finish a pre-settings until you get the password settings, then punch in 1111 Fallow button blue That point from it.

In normal use if you want to set a password for yourself

1-Go to Setup / changing the password box then press blue button punch press blue button 1111 again.
3-For Further change of pass number 1 re peat
 

tani1

Staff member
Super Moderator
Messages
17,767
Super Features Specification for (TM-5402 HD + TM-6902 HD + TM-7102)
 
Top