Super ,thankyou...
Qviart DUAL Experimental Receiver
- Thread starter raul7
- Start date
- Messages
- 17,541
Im not Viark-Qviart Team so dont know, i will ask though to see if i can find out.
There are some developers on here maybe they will know.
I have set my engine in Usals, it does not turn the engine in any way, an urgent solution must be found for this, there is no problem with the engine on the enigma 2 side, a solution must be provided on the android side, it will be very good if you report this to the authorized units...
cokeaddict
Member
- Messages
- 375
I already told you, it should be fixed in the next firmware update
Cevabınız için çok teşekkür ederim, lütfen bu sorunu geliştiricilere bildirir misiniz...
cokeaddict
Member
- Messages
- 375
It was already reported, hence it is fixed in the next update.
- Messages
- 17,541
So here is the list.
53e-30w Blind scan on all the major sat positions.
Very frustrating to do this with the duals Android scanning issues, either freezing during scans or booting you out mid scan.
There is also the issue of the Dual not always sending the dish to the correct position, so if you find channels that should not be under a specific sat or a sat positon missing well hard lines
Scan the arc yourself. you dont have to use this list 
Main reason for this and it seems to effect mainly sats on the west side, you send the dish west it goes east and starts to scan. My remote has been flung around the room on a number of occasions. This happens on either of my Usuals dishes.
I think i may have upset the Dual and its getting back on me for disturbing it from it's usual role of propping the dinning room door open
List was made with universal LNB setup.
Install list with backup & load option from a usb stick
Setup your usuals coordinates and reboot.
53e-30w Blind scan on all the major sat positions.
Very frustrating to do this with the duals Android scanning issues, either freezing during scans or booting you out mid scan.
There is also the issue of the Dual not always sending the dish to the correct position, so if you find channels that should not be under a specific sat or a sat positon missing well hard lines
Scan the arc yourself. you dont have to use this list Main reason for this and it seems to effect mainly sats on the west side, you send the dish west it goes east and starts to scan. My remote has been flung around the room on a number of occasions. This happens on either of my Usuals dishes.
I think i may have upset the Dual and its getting back on me for disturbing it from it's usual role of propping the dinning room door open
List was made with universal LNB setup.
Install list with backup & load option from a usb stick
Setup your usuals coordinates and reboot.
İşte liste.
53e-30w Tüm ana uydu konumlarında kör tarama.
Bunu, taramalar sırasında donma veya taramanın aralarında sizi başlatma gibi ikili Android tarama süreleriyle yapmak çok sinir bozucu.
Dual'in çanak anteni her zaman doğru çalıştırma gönderme sorunu da vardır, bu nedenle belirli bir uydu veya uydu konumu altında alınması gereken kanallar bulursanız, sert çizgiler eksiktir. Yayı alıntıları tarayın
Bunun ana nedeni batı ve yönleri batı olarak yan sats etkisi yapıyor gibi görünüyor, çanakya gönderiyorsunuz doğuya gidiyor ve taramaya başlıyor. Uzaktan kumandam birkaç kez çalıştırıldı içinde savruldu. Bu, Her yemek yemeklerinden birinde olur.
Tahminen Dual'i üzmüş olabilirim ve onu her zamanki yemek odası kapısını açık tutma rolünden rahatsız etmek için bana yerleşen olabilir.:emin değilim:
Liste evrensel LNB kurulumları ile kaydedilmiştir.
Bir USB bağlantısının yedekleme ve yükleme seçeneği ile yükleme listesi
Her zamanki koordinatlarınızı ayarlayın ve yeniden başlatın.
Thank you very much, I will try it, good luck to you...
- Messages
- 916
- Messages
- 916
I can confirm that open atv 7.3 on the dual does open the icam channels on 19,2. I used the dreamsat pannel to install ncam 13.7 and used a channel list that included the iptv icam channels and that they do open. Pure2 also works but i cannot get openpli or cobralibersat images to open those channels.
azerty9200
Registered
- Messages
- 42
hello, the team since I asked for the sp1 but since yesterday when I turn on my viark I receive on my dial that an update is ready I cancel, but if launch the update I risk losing my sp1 or not Thank you for your reply
bonjour, l'équipe depuis que j'ai demandé le sp1 mais depuis hier quand j'allume mon viark je reçois sur mon cadrant qu'une mise à jour est prête moi j'annule, mais si lance la mise à jour je risque de perdre mon sp1 ou pas merci de votre réponse
bonjour, l'équipe depuis que j'ai demandé le sp1 mais depuis hier quand j'allume mon viark je reçois sur mon cadrant qu'une mise à jour est prête moi j'annule, mais si lance la mise à jour je risque de perdre mon sp1 ou pas merci de votre réponse
cokeaddict
Member
- Messages
- 375
You will not lose SP1 if you update
Thankyou...
So you say, openpli and cobralibersat image, icam does not work in sky, but it works in open atv 7.3 and pure2 image?
It works on any enigma2 image , with oscam-icam or ncam emulator , and most importantly with modified bouquet ( Sky De on 19.2 for example ) for that kind of watching
You can install Ciefp enigma2 settings list , inside find modified bouquet Sky De Icam and try it , it must work , of course if Your C line open that channels
You can install Ciefp enigma2 settings list , inside find modified bouquet Sky De Icam and try it , it must work , of course if Your C line open that channels
- Messages
- 916
I have a dual and I have four images in multi-boot. Open atv and pure2 with ncam 13.7 with the correct channel list open sky de. Open pli and cobralibersat which will not install ncam 13.7 from dreamsat panel but latest Oscam with rev will. These images do not open icam for me. I have spent time trying. The box just hangs and then does not clear.
Last edited: