Hello,
I am preparing various sub sticks with different images but my original dm800hdse does not boot from them but always from flash. I made the appropriate change in bios:
usb [/autoexec.bat]
flash[none]
With this config, dm does not boot from usb but goes to ssl mode:
===========================================
...
3
COPY CODE
COMPARE CODE
4567
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox D M800SE
FIRST STAGE 1.0/400 {BO23456}
[m
2ND STAGE OK, build #84 (2011-09-01)
0.000 - BCM board setup
0.000 - fp init
0.000 - ca init
0.510 - load config
0.537 - config loaded.
* press to enter setup
OLED found!
color oled reset
lcd: BOOT #84
P23 detected!
- read config file: /boot/secondstage.conf
Device: USB Disk unit 0
- Sectors: 15261696
- Size: 7452 MiB
P 0b 63 32067 < 15261696
Device 0: Partition 1: Filesystem: FAT32 ""
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /boot/autoexec.dat
lcd: /bootnone
invalid path: /bootnone
lcd: /boot/zImage.elf
detected jffs2 blocksize: 16kb
...
======================================================
It detects usb drive but does not try boot from it isn-t it ?
There is the secondstage 84 of date 1/9/2011 installed, there are newer ssl in net, but in ipk or bin format only. how to install them ?
I try the command(ipkg not found):
opkg install /media/hdd/dreambox-secondstage_84-r12.0_dm800se.
then output:
===========================================
Installing dreambox-secondstage (84-r12.0) to root...
Configuring dreambox-secondstage.
Partition #0: 148704 of 210371 bytes (/usr/share/dreambox-secondstage/secondstage-dm800se.bin)
Erased 262144 bytes from address 0x00000000 in flash
Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x4000
Writing data to block 2 at offset 0x8000
Writing data to block 3 at offset 0xc000
Writing data to block 4 at offset 0x10000
Writing data to block 5 at offset 0x14000
Writing data to block 6 at offset 0x18000
Writing data to block 7 at offset 0x1c000
Writing data to block 8 at offset 0x20000
Writing data to block 9 at offset 0x24000
===========================================
but it is not installed, after checked is the old ssl of date 1/9/2011
Another problem is that the dm does not go to ssl mode while usb pendrive is inserted, but boots from flash.
can help me to gout of this vicious circle ??
thanks in advance
I am preparing various sub sticks with different images but my original dm800hdse does not boot from them but always from flash. I made the appropriate change in bios:
usb [/autoexec.bat]
flash[none]
With this config, dm does not boot from usb but goes to ssl mode:
===========================================
...
3
COPY CODE
COMPARE CODE
4567
(c) 2007,2008 Dream Multimedia GmbH. All rights reserved.
Dreambox D M800SE
FIRST STAGE 1.0/400 {BO23456}
[m
2ND STAGE OK, build #84 (2011-09-01)
0.000 - BCM board setup
0.000 - fp init
0.000 - ca init
0.510 - load config
0.537 - config loaded.
* press
OLED found!
color oled reset
lcd: BOOT #84
P23 detected!
- read config file: /boot/secondstage.conf
Device: USB Disk unit 0
- Sectors: 15261696
- Size: 7452 MiB
P 0b 63 32067 < 15261696
Device 0: Partition 1: Filesystem: FAT32 ""
- failed to open /boot/secondstage.conf
- failed to open /cf/autorun.bat
lcd: /boot/autoexec.dat
lcd: /bootnone
invalid path: /bootnone
lcd: /boot/zImage.elf
detected jffs2 blocksize: 16kb
...
======================================================
It detects usb drive but does not try boot from it isn-t it ?
There is the secondstage 84 of date 1/9/2011 installed, there are newer ssl in net, but in ipk or bin format only. how to install them ?
I try the command(ipkg not found):
opkg install /media/hdd/dreambox-secondstage_84-r12.0_dm800se.
then output:
===========================================
Installing dreambox-secondstage (84-r12.0) to root...
Configuring dreambox-secondstage.
Partition #0: 148704 of 210371 bytes (/usr/share/dreambox-secondstage/secondstage-dm800se.bin)
Erased 262144 bytes from address 0x00000000 in flash
Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x4000
Writing data to block 2 at offset 0x8000
Writing data to block 3 at offset 0xc000
Writing data to block 4 at offset 0x10000
Writing data to block 5 at offset 0x14000
Writing data to block 6 at offset 0x18000
Writing data to block 7 at offset 0x1c000
Writing data to block 8 at offset 0x20000
Writing data to block 9 at offset 0x24000
===========================================
but it is not installed, after checked is the old ssl of date 1/9/2011
Another problem is that the dm does not go to ssl mode while usb pendrive is inserted, but boots from flash.
can help me to gout of this vicious circle ??
thanks in advance