Recent content by Del_RFC

Hi Been around for years but not posted much. With the death of DVB-S I decided to install a DVB-C tuber in my clone DM800HD. Tuner installed and all looked fine - time for a new image. The box showed BL75 via telnet but on further investigation I believe it is a BL72. After NO CA Errors...

I have an old DM800HD BL72 with a motorised dish. About a year ago I replaced my old bracket with a K Mount to firm up the dish mounting after a few problems with stormy weather. After a fair bit of messing around I managed to get a decent alignment with 28.2 sitting in the 90%+ signal...

I am running a DM800HD on a motorised 1m dish. Getting very good signals across the arc but have a very strange problem with Sky Italy HD. Just been on the roof, made sure everything is bang on square and I am confident the movement across the arc is good. I can get all channels Sky Italy non...

I have a DM800S (clone) and been running on a motor for quite some time. Recently after high winds blew my dish out of alignment I fitted a new T & K Bracket and everything has been rock solid since. Last week whilst pissing about I uploaded a new file of settings I lost everything on the...

Sorry to be a pain again. I have a DM800S om a motorised set up. The bracket holding the motor and dish was a wee bit lightweight and I had a few issues with the high winds. Decided to replace the bracket today with a T & K bracket and the whole thing is now rock solid. Realignment I...

I have a DM800s with a motor fitted. From this afternoon I have had an issue with the tuning of everything but FTA channels. I can access FTA on all the usual satellites with good/excellent signal strength which would suggest alignment is good however every single "pay channels" shows zero on...

Apologies if this a silly question. I have a DM800S dreambox hooked up to a motorised dish with a single universal LNB. I am looking to add a second box (DM500S) into my bedroom. Can I simply change my LNB to a dual. Run LNB feed 1 exactly as it is just now to my DM800S continuing to control...

Hi, Can anyone assist with a strange one. I have been trying to set up a mates DM500s with a motorised dish with limited success. As far as alignment etc is concerned all is bang on at 0.8W, 13E 19.2 with crystal clear reception, high signal strength and low BER. When trying to scan 28.2E it...

Can anyone advise the impact replacing the satellite.xml file will have on my current settings. I have just spent a week setting up a motorised system and it is running beautifuly. I want to add a few more satellites that are not in my current .xml file so have created a new one. By FTP'ing...

Run into some problems trying to tune in my DM800s afetr fitting a motor. I have the dish aligned to Thor 0.8 and after a scan all channels are clear with a decent signal being received and all HD is glicth free. I have set up the receiver using USALS to hit 28.2e and all the others of any...

Got an issue I am struggling to resolve. Box boots and shows an IP address of 192.168.0.167 both when loading and when stopped for flashing via HTTP. I cannot access this address either via HTTP or by pinging it. When the box loads the IP address is changed to 192.168.2.5 which is visible in...

Returned my dead box to my UK supplier and he very quickly replaced it. So far so good.... The problem is when I have plugged it in it immedietly goes to an error message in the LCD - (No number). Spoke to the dealer who reckons it is softwaqre related and advises that I try load an image via...

Hi, Powered my DM800S down and plugged in a USB HDD (to check if it would recognise MKV files). With the HDD connected via the lower USB the box has never booted since.:confused: I have powered it on / off as per many posts. All I am getting is the two ethernet lights. Any guidance would be...

Is there any way of playing these MKV files which I have already saved on an external USB hard drive? I also have a few DVD images and Divx files but not too worried about them. I have a DM800S HD (clone) with Nabilosat Black Hole Hyperspace with Meoboot (BL72) image loaded. No internal HDD...

Hi Guys, I am new to Dreambox & CS but already excited at the prospect of what these boxes can do. I have been on teh scene with cable for quite some time and many moons ago had a d2mac set up pre digital. My DM800S HD Clone arrives tomorrow. BL 72 with Gemini 4.5 pre installed. Plan is to:-...