New firmware hdl 5.36 arab

New firmware hdl 5.36 arab by SIDIAISSA
The new in this firmware is:

*Arabic language aded now 5 langues in firmware
*Support ird2 ART and SHOW work with daily key
*Some mod in grafic

Hello vegeku90, I've put in this fw yesterday because I'm interested in a*t channels at 7w, but I got nothing. I seem to understand that I've got to use the program mediasatconnect, is that right? I did and I even uploaded a bin file named "lista nilsat" or something and then I put in the new keys by remote. But it won't work. Have you tried i2 channels yourself? Is there anything else I need to do?
Thanks

not tested by me mate but source was shure;)

you must put daily keys

i did put the daily key, I've tried a couple hours ago too. Can you ask your source the exact procedure? I've seen a pic on a different board where it was used mediasatconnect and "1530" was highlighted as if it was important to load the file this way. I've tried but it's a no go

thanks

Everything ok now! Dunno what happened, I've put in the same file with the same keys that didn't work this morning, and now it works :thum:

hi cydonia84,
I have downloaded this firm with lookerflach to see ar*t channels but there nothing new, can you tell me what to do and how to use mediasatconnect?

hi cydonia84,
I have downloaded this firm with lookerflach to see ar*t channels but there nothing new, can you tell me what to do and how to use mediasatconnect?

I thought mediasatconnect was necessary, but it turned out it's not. I used corvoboys gbtool instead and that was it. Put in active keys, the right id (0*0*0*6*0*4); if it doesn't work, try switching to mcam (+ pers 5 and then press 2)

I thought mediasatconnect was necessary, but it turned out it's not. I used corvoboys gbtool instead and that was it. Put in active keys, the right id (0*0*0*6*0*4); if it doesn't work, try switching to mcam (+ pers 5 and then press 2)
thank you very much, but tell, do you mean that all I have to do is to Load the firmware "hdl 5.36 arab" with gbtool and that's all?
plz tell all I have to do cause it's a long time that i'm trying to see ar*t on my dsx 6072 but in vain....
thank you in advance.

thank you very much, but tell, do you mean that all I have to do is to Load the firmware "hdl 5.36 arab" with gbtool and that's all?
plz tell all I have to do cause it's a long time that i'm trying to see ar*t on my dsx 6072 but in vain....
thank you in advance.

I've uploaded the firmware with lookerflash, as I always do, then I've used gbtool to send the channel list and the emu file.
Just remember the mcam thing...

thanx, but the problem is that i tried to send the emu with gbtool but no transmission happens , i don't know why?

You need to go to pers - 9 - 3 so that the GB can communicate with gbtool, did you do that? If you already did, try and set the speed at 9600 on both the gb (pers - 4 - 1) and in gbtool.

I did that by following the instructions in the gbtool, but sill no transmission. i entered the keys by remote and it's ok, i have the a*rt channels. thank you very much for your help.

just out of curiosity, does it work with both mcam and mken?

no, it didn't work untill i changed the mken to mcam. all was black with mken. what about the show*time? does it work with you?
thanx again.

no, it didn't work untill i changed the mken to mcam. all was black with mken. what about the show*time? does it work with you?
thanx again.

No, up until the end of july I used to watch show**** on a pc dvb card, before this 5.36 fw came out. But there are no active k*ys available at the moment.

and by the way , can you recommend to me a site from where i can download the latest "emu" to inject in my dsx 6072?
thank you in advance.

and by the way , can you recommend to me a site from where i can download the latest "emu" to inject in my dsx 6072?
thank you in advance.

I sent you a pm

thank you very much for the message and for the link, but the problem is that i did everything including the changes in receiver, but still i have no transmission of the emu because i can't get a connection... I don't know why !!!!!

I don't know, just make sure you select the right com port and that the gbtool speed is the same as the GB. It should work. Isn't it possible the cable is damaged? Try and go into service mode with Lookerflash.
Otherwise try out another software to send the emu.

thank you for all the useful advices i got from you...

thank you for all the useful advices i got from you...

So, were you able to send the file?

Hi,
no i couldn't although i tried everything; I changed the baud rate to 9600 and i did the same with my receiver, but still no connection and tried another program "EMUKreator" and again no transmission !!! i still don't know why? so all i do is put the keys by hand with the remote.

Have you tried putting it into service mode with lookerflash? If it doesn't, it could be a cable problem.

i don't think it's the cable, because i have used it recently to program my receiver with the last hdl 5.36.