Translated from Spanish to English with google
Update errors in the firm and solution on models Mvision
Collection of errors MVision
As I see you've got more of a problem with the deco, I have given a tour of the network and copy-paste base (ciental-Danitrapella) I have compiled this info that I leave with you to be your help ... Let go ahead that work is not mine, because I do not intend to assign him a job that is not for me to ...
Red Eye Syndrome
- We call Syndrome "Red Eye" a mistake that can be observed if the receiver turns on and is not the red LED's Fontal lit on a permanent basis.
There are several reasons why q CPU can not run the operating system (firm):
One is hard, a fault in the power supply would cause q feed of the flash that keeps the firm does not perform correctly and
therefore could not access it from the cpu, therefore, red eye. Not having suffered such damage can not really indicate what the fault q occurs at the source and whether we can fix it ourselves to avoid having to refer our q receiver to a specialized center.
On another occasion, the most common, it is a mistake or a fault during the process of updating the firm. Here are q make a point in 2 ways we have to enter q:
- SOFTWARE UPGRADE: There is no erasing the previous software. The new firm will overwrite the old. So if the process is interrupted for any reason, or an error occurs in the load q get only what is an error of cheksum. the famous ERROR 0
- Bootloader UPGRADE: For a full erase the flash before introducing the new firm. Q as if the process is interrupted or the wrong result will be a nice red eye in our receiver. Because the OS is incomplete or corrupt and will not start
First solutions:
* Unplug the power for a few minutes. If not resolved:
* Attempting to force the burden of the firm in the deco (As you press the button "software upgrade," turn on the deco (give current). Sometimes it works)
* JTAG
Err. 0
Tends to happen when it turns off before you have the deco Good on the display.
Forcing the burden of the firm. Indications of Mitega friend to fix the error 0:
1-Conectas Deco PC with a button back off
With a 2-Utils MvisionE + das firm to charge and says that although there is no continuous deco
3-Choose upgrade software, choose the firm you're going to get (a best original), and gives a start
The 4-Utils mvisionE + show "d000", now turns on the deco (BROUGHT Err0 in the display) off and then turn it on again. And this, you should upload (This firing Shutdown and lighting must be done without much later).
If not what it takes to first, keep trying until it caught q.
Although the display says "ERRO 0" if apretamos with both the volume buttons on the deco of the two at a time, we will see that the display says "092" if we make the burden of the firmware using the pulsed although not detect pc connection deco-The firw is introduced without problems, on the computer when the word good, release the buttons on the volume and we will see that starts to climb up to finish F001 and the word "GOOD".
Reboot loop after loading a list (by Phenixa222)
It can happen by mistake, or charge you anything after unawareness that the deco, that we continually restart. Recently, a past with the lists of channels, and why / solution is this:
When you load a list of channels to a deco FCIS7000, E + / Combo / Terrestrial / Cable, etc ... We always kick off the deco on Channel 1.
If that channel is a channel that does not support our deco deco to enter into a boot loop, showing firmw, will go to the channel, and restarts. Examples of Decos and channels are:
FCIS 7000 / E + does not support DTT channels or Cable
FCIS 7000T does not support satellites or cable channels
FCIS 7000C does not support or DTT channels Satellite
FCIS 7000B/Combo not supported cable channels
To get out of that loop just charge you a list good for our optimal model.
Just channel 1 is a channel for our deco, and if we have some channels that are not for our model can be deleted from the menu of deco. The problem will be in the loop, do not let us put it into shock.
Do the following:
1. 2nd EuroScart connect to a device that sends automatic switching (DVD, Video, etc ...)
2. Turning the deco ...... The deco, the switch to turn on the signal of No. 2 EuroScart, and will not restart.
3. We load a list, bearing in mind that the deco kick off on Channel 1.
Bone that if the deco is a combo without FCIS, Metais NOT READY TO ENGAGE IN THE CHANNELS DTT CHANNEL 1 (like the one that comes with firmw redsin). Any other if you can get (Case of Phe_VII_sat_revx ...), but remember to erase ls DTT with the menu of deco. Will not fall NEVER IN A CANAL DTT IF YOUR DECO IS NOT FOR THIS REASON
Err.3
* Error of communication. (almost certainly because of cable)
Err.4
* Return to download the software from the web and try again.
Err.6
* It occurs when trying to load a firmware whose software is incompatible with our Boot ex. we have a Boot *. UPB and get a *. bin Firm
Solution: The answer carrying a firmw. But as the official boot and then he got a list of channels, and finally with a fimw magic of the man max. and voila running.
Certainly we must proceed with the error 0 as the computer does not recognize the deco. back started to send off the boot and firmw as 2 or 3 seconds back jacks. But JTAG
Err.8
* The cables make bad contact 2-3, 5-5 on this well because it is what gives "Connection established."
Err.9
* It seems to be a problem ... the pen is recommended format and reload firm or do it via
Mvison utils ... "If this is the first time that cambiais firm to do so via Port series (be sure of getting the firm correct)
Connection error by FAR @ MIR
If you have this problem try to follow these steps to communicate with the deco.
1 From the deco disconnected from the flow and switch back off and then plug it in to put on, wait until you leave the display 2:00 (In the summer time in winter should always talking to leave 1:00 Spain). Do not connect the cable nullmodem yet.
2nd With a null cable connected to pc, but still not the deco, run the program and click on setup boxloader comm, gonna set a window where the port where we have connected the cable, do not accept either cancel or close the window that opens, just put the COM port number and go to point 3.
3 Connect the cable to accept deco and in the window that we have left in the program boxloader, then gonna a progress bar and connection established, in the main window will appear boxloader of hard data and fw and you can send or receive data the deco.
Appears by setting the word "Boot" on the display
The ruling is normally the source of food gives us misaligned tensions over its value.
The fault is two capacitors 1000pf 10V, the cause is the 10V q are just "8080 comes with capacitors 16v"
Solution to replace the capacitors on 1000pf some of 25V
Before if you can force the burden of Interto Firm (as they say Gatonegro and Angel_Blanco) to see if they can continue to solve the Handbook of error 0 making it as the last paragraph. This last step does not always work, because if the condenser will have to change it irrevocably.
Deco blocked by (humor)
When the deco is blocked, appearing just a few strokes in the red display and without a time. And disconnecting ago does not work.
Revive the bug in the same way: With the boxloader tried to read "Read user data". But can not get back after shutting down and re-acenderlo already makes the "boot"
Error LNFB
Well-m visioneros only say that if this happens to you, LNFB intermittent error, is that you have the antenna cable that goes to the wrong deco, and revise it solved.
Error123 and ---- In the Display
The possible cause is a communication error between deco and PC. which carries a load of bad Firm. We will have to force the burden of the firm, there is a manual explaining in this section
Cloning Decos
When the failure to resolve these errors, you can always try to clone your deco with another of the same model. Often given successful:
Here you leave the manual to clone two Decos mvision. Q Remember this must be done with an original signature. If someone decides to do with another type of firm, aunk works equally, needs to know q is against the law.
MANUAL FOR OUR CLONE Decos
-------------------------------------------------- ------------------------------
1) Plug the 2 Decos to light .. turn on the switch without any ass.
2) Activate the switch back deco master (of the bone that want to copy the information).
3) We connect the Decos one another through the null modem cable.
4) Turn on the slave deco (ke keremos to send the information) ..
5) We will see as a start to go up and down little acts .. etc so hopefully ke ke finish up their accounts 2 (better if you put good, but because we hope to put ke F100 u100 .. better after letting a ratillo ke reach this point)
6) stopping the 2 Decos switch back .. and disconnect all cables ..
7) To prove it
It is essential to know which firm will take place and that appears on the display in case of error, to be able to discuss with the teachers walking around here, it may be due and its possible solution ...
If anyone has more info about errors or possible solutions not hesitate to bring it to be able to help ... I remember that the use of this info is always under your responsibility ...
by NASLUND
saludos señores
Update errors in the firm and solution on models Mvision
Collection of errors MVision
As I see you've got more of a problem with the deco, I have given a tour of the network and copy-paste base (ciental-Danitrapella) I have compiled this info that I leave with you to be your help ... Let go ahead that work is not mine, because I do not intend to assign him a job that is not for me to ...
Red Eye Syndrome
- We call Syndrome "Red Eye" a mistake that can be observed if the receiver turns on and is not the red LED's Fontal lit on a permanent basis.
There are several reasons why q CPU can not run the operating system (firm):
One is hard, a fault in the power supply would cause q feed of the flash that keeps the firm does not perform correctly and
therefore could not access it from the cpu, therefore, red eye. Not having suffered such damage can not really indicate what the fault q occurs at the source and whether we can fix it ourselves to avoid having to refer our q receiver to a specialized center.
On another occasion, the most common, it is a mistake or a fault during the process of updating the firm. Here are q make a point in 2 ways we have to enter q:
- SOFTWARE UPGRADE: There is no erasing the previous software. The new firm will overwrite the old. So if the process is interrupted for any reason, or an error occurs in the load q get only what is an error of cheksum. the famous ERROR 0
- Bootloader UPGRADE: For a full erase the flash before introducing the new firm. Q as if the process is interrupted or the wrong result will be a nice red eye in our receiver. Because the OS is incomplete or corrupt and will not start
First solutions:
* Unplug the power for a few minutes. If not resolved:
* Attempting to force the burden of the firm in the deco (As you press the button "software upgrade," turn on the deco (give current). Sometimes it works)
* JTAG
Err. 0
Tends to happen when it turns off before you have the deco Good on the display.
Forcing the burden of the firm. Indications of Mitega friend to fix the error 0:
1-Conectas Deco PC with a button back off
With a 2-Utils MvisionE + das firm to charge and says that although there is no continuous deco
3-Choose upgrade software, choose the firm you're going to get (a best original), and gives a start
The 4-Utils mvisionE + show "d000", now turns on the deco (BROUGHT Err0 in the display) off and then turn it on again. And this, you should upload (This firing Shutdown and lighting must be done without much later).
If not what it takes to first, keep trying until it caught q.
Although the display says "ERRO 0" if apretamos with both the volume buttons on the deco of the two at a time, we will see that the display says "092" if we make the burden of the firmware using the pulsed although not detect pc connection deco-The firw is introduced without problems, on the computer when the word good, release the buttons on the volume and we will see that starts to climb up to finish F001 and the word "GOOD".
Reboot loop after loading a list (by Phenixa222)
It can happen by mistake, or charge you anything after unawareness that the deco, that we continually restart. Recently, a past with the lists of channels, and why / solution is this:
When you load a list of channels to a deco FCIS7000, E + / Combo / Terrestrial / Cable, etc ... We always kick off the deco on Channel 1.
If that channel is a channel that does not support our deco deco to enter into a boot loop, showing firmw, will go to the channel, and restarts. Examples of Decos and channels are:
FCIS 7000 / E + does not support DTT channels or Cable
FCIS 7000T does not support satellites or cable channels
FCIS 7000C does not support or DTT channels Satellite
FCIS 7000B/Combo not supported cable channels
To get out of that loop just charge you a list good for our optimal model.
Just channel 1 is a channel for our deco, and if we have some channels that are not for our model can be deleted from the menu of deco. The problem will be in the loop, do not let us put it into shock.
Do the following:
1. 2nd EuroScart connect to a device that sends automatic switching (DVD, Video, etc ...)
2. Turning the deco ...... The deco, the switch to turn on the signal of No. 2 EuroScart, and will not restart.
3. We load a list, bearing in mind that the deco kick off on Channel 1.
Bone that if the deco is a combo without FCIS, Metais NOT READY TO ENGAGE IN THE CHANNELS DTT CHANNEL 1 (like the one that comes with firmw redsin). Any other if you can get (Case of Phe_VII_sat_revx ...), but remember to erase ls DTT with the menu of deco. Will not fall NEVER IN A CANAL DTT IF YOUR DECO IS NOT FOR THIS REASON
Err.3
* Error of communication. (almost certainly because of cable)
Err.4
* Return to download the software from the web and try again.
Err.6
* It occurs when trying to load a firmware whose software is incompatible with our Boot ex. we have a Boot *. UPB and get a *. bin Firm
Solution: The answer carrying a firmw. But as the official boot and then he got a list of channels, and finally with a fimw magic of the man max. and voila running.
Certainly we must proceed with the error 0 as the computer does not recognize the deco. back started to send off the boot and firmw as 2 or 3 seconds back jacks. But JTAG
Err.8
* The cables make bad contact 2-3, 5-5 on this well because it is what gives "Connection established."
Err.9
* It seems to be a problem ... the pen is recommended format and reload firm or do it via
Mvison utils ... "If this is the first time that cambiais firm to do so via Port series (be sure of getting the firm correct)
Connection error by FAR @ MIR
If you have this problem try to follow these steps to communicate with the deco.
1 From the deco disconnected from the flow and switch back off and then plug it in to put on, wait until you leave the display 2:00 (In the summer time in winter should always talking to leave 1:00 Spain). Do not connect the cable nullmodem yet.
2nd With a null cable connected to pc, but still not the deco, run the program and click on setup boxloader comm, gonna set a window where the port where we have connected the cable, do not accept either cancel or close the window that opens, just put the COM port number and go to point 3.
3 Connect the cable to accept deco and in the window that we have left in the program boxloader, then gonna a progress bar and connection established, in the main window will appear boxloader of hard data and fw and you can send or receive data the deco.
Appears by setting the word "Boot" on the display
The ruling is normally the source of food gives us misaligned tensions over its value.
The fault is two capacitors 1000pf 10V, the cause is the 10V q are just "8080 comes with capacitors 16v"
Solution to replace the capacitors on 1000pf some of 25V
Before if you can force the burden of Interto Firm (as they say Gatonegro and Angel_Blanco) to see if they can continue to solve the Handbook of error 0 making it as the last paragraph. This last step does not always work, because if the condenser will have to change it irrevocably.
Deco blocked by (humor)
When the deco is blocked, appearing just a few strokes in the red display and without a time. And disconnecting ago does not work.
Revive the bug in the same way: With the boxloader tried to read "Read user data". But can not get back after shutting down and re-acenderlo already makes the "boot"
Error LNFB
Well-m visioneros only say that if this happens to you, LNFB intermittent error, is that you have the antenna cable that goes to the wrong deco, and revise it solved.
Error123 and ---- In the Display
The possible cause is a communication error between deco and PC. which carries a load of bad Firm. We will have to force the burden of the firm, there is a manual explaining in this section
Cloning Decos
When the failure to resolve these errors, you can always try to clone your deco with another of the same model. Often given successful:
Here you leave the manual to clone two Decos mvision. Q Remember this must be done with an original signature. If someone decides to do with another type of firm, aunk works equally, needs to know q is against the law.
MANUAL FOR OUR CLONE Decos
-------------------------------------------------- ------------------------------
1) Plug the 2 Decos to light .. turn on the switch without any ass.
2) Activate the switch back deco master (of the bone that want to copy the information).
3) We connect the Decos one another through the null modem cable.
4) Turn on the slave deco (ke keremos to send the information) ..
5) We will see as a start to go up and down little acts .. etc so hopefully ke ke finish up their accounts 2 (better if you put good, but because we hope to put ke F100 u100 .. better after letting a ratillo ke reach this point)
6) stopping the 2 Decos switch back .. and disconnect all cables ..
7) To prove it
It is essential to know which firm will take place and that appears on the display in case of error, to be able to discuss with the teachers walking around here, it may be due and its possible solution ...
If anyone has more info about errors or possible solutions not hesitate to bring it to be able to help ... I remember that the use of this info is always under your responsibility ...
by NASLUND
saludos señores