Setup my MOTECK SG-2100A

prenses · Jun 17, 2008

Hello everyone,

I own a MOTECK SG-2100A, included a Triax 80 cm dish with one lnb. What is the procedure to setup it in the IPBox 9000 HD?
In the manual I can't found something where they described it.

Perhaps is there someone he can gave me a link or a document where they describe this procedure.

Thanks for your co-operation.

Best regards,

Peter Renses

xxxAxxx · Jun 17, 2008

at the moment ipbox will not save your setting positions correctly...

this why u should use Usals option working %100

prenses · Jun 17, 2008

xxxAxxx said:
at the moment ipbox will not save your setting positions correctly...

this why u should use Usals option working %100

Thanks,

So at this moment I can only use it optimal with Usals.

Can you gave me some advices how to starts and where to begins with the reference point?

Best regards,

Peter Renses

xxxAxxx · Jun 17, 2008

menu--service searching--usals

select your sat

enable--usals

hit the green button

in the new window enter your
longitude
and
latitude

dish will move if the value is correct to that sat...

exampel:is you select hotbird transponder set on strong Tp like 11766

prenses · Jun 17, 2008

xxxAxxx said:
menu--service searching--usals

select your sat

enable--usals

hit the green button

in the new window enter your
longitude
and
latitude

dish will move if the value is correct to that sat...

exampel:is you select hotbird transponder set on strong Tp like 11766

Thanks,

But must I select one sat or more? And are the longitude
and latitude the same for every sat I selected.

And what do you ment with "strong Tp like 11766"

Thanks,

Peter Renses

xxxAxxx · Jun 17, 2008

you will have the list
menu--service searching--usals

select your sat

enable--usals

now if you enter the value's like
longitude
latitude

on one sat you dont need to enter on other sat's

if you enable usals for this exampel:

hotbird 13*E
Astra 19*E
Nilesat7*W

dish will move to that sat...

when you want to tune your sat before the usals setting you must enter the strog tp signal in that sat this why ........

if you enter your long and lat and if you select a invalid tp you will think usals not working properly.......

you must select a strong tp before you enable the usals for that sat...

prenses · Jun 17, 2008

xxxAxxx said:
you will have the list
menu--service searching--usals

select your sat

enable--usals

now if you enter the value's like
longitude
latitude

on one sat you dont need to enter on other sat's

if you enable usals for this exampel:

hotbird 13*E
Astra 19*E
Nilesat7*W

dish will move to that sat...

when you want to tune your sat before the usals setting you must enter the strog tp signal in that sat this why ........

if you enter your long and lat and if you select a invalid tp you will think usals not working properly.......

you must select a strong tp before you enable the usals for that sat...

Thanks for you support.

I'm living in the Netherlands and in the place Groningen.

I will try it this evening. So I must not upload a channel list because they don't work?

Also my receiver responds very slowly to the receiver, is this a common problem or have you another suggestion?

Thanks again for your advice!!

Peter

xxxAxxx · Jun 17, 2008

yes you can upload your channel list no problem but be fore you upload the the box go on the editor-Lnb edit remove all the sat if they set on diseqc or 1.2 save and send did to your box...and flow how i told you....

receiver not slow you must have a lot of file in the reciver.... pls do not upload every think on the net regarding this box....

prenses · Jun 17, 2008

xxxAxxx said:
yes you can upload your channel list no problem but be fore you upload the the box go on the editor-Lnb edit remove all the sat if they set on diseqc or 1.2 save and send did to your box...and flow how i told you....

receiver not slow you must have a lot of file in the reciver.... pls do not upload every think on the net regarding this box....

Thanks,

I will follow your instructions. And I don't have configured in de box diseqc 1.2

No haven't a lot of files stored on the box, perhaps reject the image again. Because I don't have UBoot 1.3 because I'm afraid about the error ER 10.

Best regards,

Peter renses

xxxAxxx · Jun 17, 2008

let's clear now....
image you're using at the moment is ABcom 7219

if yes it's better you upload the ubot 1.3.1 if not....

pls go back to sifteam image.....