DVB-S2 Channels not working...Help wanted

indinana

Senior Member
Messages
105
I have get original dreambox 800hd and install nabilo blackhole v.012. The problem is that No any of Dvb-s2 signal available, either hotbird 13E or eurobird 9 9E. all other DVB-s channels working very well.
I have made all my efforts but to no avail.
I m using 6 feet solid dish.

A guide in this regard will be highly appreciated.
Thanks
 

johnlonghair

Member
Messages
66
no dvb-s2

Hi indinana,
Try a manual scan for every satelitte seperatly.

Press Menu button on remote.
Select : setup - service searching - manual scan

Change "type of scan" to "single satelitte".
Use the arrowkeys left and right of the OK button to change.
(The tuner will change automaticly to DVB-S2 now.)

Change "satelitte" to the satelitte you want to scan (eurobird or hotbird).

"Networkscan" should be "yes"
"Clear before scan" should be "no"
"Only free scan" should be "no"

Now press the "OK" button on the remote.


If the HD channels are not found you could try to search per transponder.

Change "type of scan" to "single transponder".
Change "system" to "DVB-S2"
Change "satelitte" to the satelitte you want to scan (eurobird or hotbird).
Enter the "frequency" you want to scan.
(Data can be found on www.lyngsat.com)
"Inversion" is "auto"
Enter the "symbol rate"
Enter the "Polarity" (horizontal or vertical)
"FEC" change it or leave it on "Auto"
"Networkscan" should be "no"
"Clear before scan" should be "no"
"Only free scan" should be "no"

Now press the "OK" button on the remote.

Grtz john
 

alias1

Senior Member
Messages
111
Thanks for replies.
The problem still exists.
I have checked with all the possibilities/setting but there is no dvb-s2 signals is receiveable.

Brohter ALIAS1..........
What is best sulotion to solve this problem if the tuner have some error. Is there any possibility to repair it?
Some forums have a fix that involves putting a capacitor on the tuner board
 

monza42

Well Known Member
Messages
694
Hi
Sorry to say this but the BH 0.12 Image is a
bit "Old"
First of all Update the Image with the Latest Drivers
but be sure that you take the OE 1.5 Driver´s
Second Replace the sat.xml from your Image
with a new one i would recommend Reinh@rd´s Sat.xml
You can find the sat.xml on your Box in /etc/tuxbox
If you have done this make a Manual Rescan as johnlonghair
avowed to you in his Post.
 

dktn

Senior Member
Messages
300
i have problem with DVB-s2 too. when change channel to DVB-s is OK but to DVB-S2 it appear "tuner failed" then "no data on tranfomer" and wait for 2-3 minutes it works.
can someone have the same mistake with me then show me what to do
(my dm800 is clone, bl 72, image release dm800 2.8.4)
 

alias1

Senior Member
Messages
111
i have problem with DVB-s2 too. when change channel to DVB-s is OK but to DVB-S2 it appear "tuner failed" then "no data on tranfomer" and wait for 2-3 minutes it works.
can someone have the same mistake with me then show me what to do
(my dm800 is clone, bl 72, image release dm800 2.8.4)
Had the same problem replaced the tuner now fine
 

dktn

Senior Member
Messages
300
I use Diseqc 4x1, dm800 clone ss72. I have to wait 2 minutes from DVB-s2 3558v2500 fec 3/4 8sqec(LNB2) to DVB-s2 10968h28800 fec 5/6 8sqec(lnb3). If i change to dvb-s it works ok. I do not know Why? is there any method to solve it.
 

alias1

Senior Member
Messages
111
I use Diseqc 4x1, dm800 clone ss72. I have to wait 2 minutes from DVB-s2 3558v2500 fec 3/4 8sqec(LNB2) to DVB-s2 10968h28800 fec 5/6 8sqec(lnb3). If i change to dvb-s it works ok. I do not know Why? is there any method to solve it.
Read my last post
 
Top