AAF Recovery Tool Atevio700-7000

marcel
06-05-2010, 10:22
Beschreibung:
AAF Recovery Tool 3.7 av700
====================


V3.7

- add small change to bootstop (2de)
- add new resellers (AV700)


V3.6

- add write all settings to box (button)
- add small change to bootstop (try to connect before serial received)

V3.5

- fix install Maxi Rev1.1/original Uboot with USB-device

V3.4

- update original recovery image to FS v1.08.16 FS 90xEU Apr 30 2010

V3.3

- add uflasherOrg_1.21_2.23 (original Uboot for AV700/AV7000)

V3.2

- add Maxi U-boot Rev1.1 for AT7000/AT700

V3.1b (AT7000)

- add reseller-id for Astro ASR1200 (111)

V3.1a

- add picture of the box (to avoid wrong use)

V3.1

- update original recovery image to FS/HS v1.08.09 FS/HS 95xEU Apr 01 2010
- fix when crc starts with a zero

V3.0

- update original recovery image to FS v1.08.01 FS 90xEU Mar 23 2010
- remove not used bootargs with set default bootargs
- add if port < 1024, abort upload and restart upload again (to get a higher port number)
- add fix for crc-check fault, forse Tftp packages size to 512. ( this is default for the uboot when packes size is not acknowledged)


Note: Use the forse Tftp packages size to 512 when you get the "CRC check Failed" message.



V2.8

- hide non used bootargs

V2.7

- add Maxi U-boot Rev1.0 for AT7000

V2.6

- add Maxi U-boot Rev0.8 for AT7000 (needed for original FW 097)
- update original recovery image to FS v1.07.97 FS 90xEU Mar 09 2010
- add wait time after usb reset

V2.5a

- add read current reseller-id
- update ART for 700 (same as ART 7000)

V2.5

- add change reseller-id
- change original recovery image back to FS v1.07.89 FS 90xEU Feb 3 2010
- update original recovery image to FS v1.07.94 FS 90xEU Feb 26 2010

V2.4a

- fix for crc failed when maxiuboot installed (first try AT7000)

V2.4

- add new Maxi U-boot Rev 0.7 with dimming Display (AT700)


V2.3

- fix bug with empty lines in custombootargs.txt

V2.2

- add load recovery image, Maxi Uboot, Original Uboot from USB devices
- add save bootargs to disk
- add custom bootargs file (use your own bootargs as default)
- add custom bootargs editor
- add "S-USB1", "S-USB2", etc... selection as boot device.


format a USB-Stick as fat32, copy the needed file from ART path to USB=Stick.
Then put your stick in the front USB-Port. (remove all other USB-devices)

The custom bootargs file must be created by the user.
It must be stored in the same dir as ART.
The file name = custombootargs.txt.
Use only one line for each bootarg !!!

Before you can use it you can created it.
There are 3 way's to do this.

1. create the file by hand and store it in the ART dir.
2. connected ART to your box and save the current bootargs as custombootargs.txt in the ART path.
3. press the "Edit Custom" button, this will create a empty file. Copy your settings and save it before exit.

YOU ARE RESPONSIBLE FOR YOUR OWN BOOTARGS SETTINGS !!!

To use the custom bootargs you have to checked the checkbox "Custom".



V2.1

- add Maxi U-boot Rev 0.7
- read Mac-adress from EEPROM ( only when Maxi U-boot installed )

V2.0

- fix bug erasing particial bootloader
- add logging, .../logs/art_log.txt

V1.9

- add Flash Original image (created from cat /dev/mtd7 with original image in flash)

V1.8

- update original recovery image to FS v1.07.89 FS 90xEU Feb 3 2010

V1.7

- fix syntax fault writing bootcmd_3
- remove writing mac address in set defaults
- save comport
- add Boot menu timeout

V1.6

- add select default boot
- add check for wrong IP format

V1.5

- remove all UFS910 entry's

V1.4

- add flash E2 image (only enabled when Maxi U-boot is installed)

V1.3

- again fix bootstop for Original U-boot for AT7000 (change timing)

V1.2

- add Maxi U-boot Rev0.5 for AT7000
- add Recovery, install Original image + erase E2 flash + erase bootsector maxi U-boot for AT7000

V1.1

- add read current settings from box (view ip, serverip, mac, ...)
- disable buttons when write ip, serverip, mac, ...

V1.0

- add install Original U-boot 1.1.2 for AT7000
- fix bootstop for Original U-boot for AT7000

V0.9

- add Maxi U-boot Rev0.4 for AT7000
- add timeout for installing maxi/original U-boot for AT7000

V0.8

- add default bootargs for AT7000

V0.7

- add Maxi U-boot Rev0.3 for AT7000


NOTE:

1. you must have installed NetFrameWorks 2.0 or higher.
2. check your firewall for use of the Tftp (port 69 and random data port)
3. for windows Vista or windows 7 you must run it as administrator
4. make sure you have no other Tftp-server running on your pc
5. make sure the files in the AAF Recover Tool dir are accessible (read access)
6. First set the correct IP's and Mac adress !!!
7. after setting the Mac adress (ethaddr) you need to reboot, otherwise the PING doesn't work !!!



Download (http://www.megaupload.com/?d=6DCKY34W)

marcel
06-05-2010, 10:25
Beschreibung:
AAF Recovery Tool 3.7 AV7000
======================


V3.7

- add small change to bootstop (2de)
- add new resellers (AV700)


V3.6

- add write all settings to box (button)
- add small change to bootstop (try to connect before serial received)

V3.5

- fix install Maxi Rev1.1/original Uboot with USB-device

V3.4

- update original recovery image to FS v1.08.16 FS 90xEU Apr 30 2010

V3.3

- add uflasherOrg_1.21_2.23 (original Uboot for AV700/AV7000)

V3.2

- add Maxi U-boot Rev1.1 for AT7000/AT700

V3.1b (AT7000)

- add reseller-id for Astro ASR1200 (111)

V3.1a

- add picture of the box (to avoid wrong use)

V3.1

- update original recovery image to FS/HS v1.08.09 FS/HS 95xEU Apr 01 2010
- fix when crc starts with a zero

V3.0

- update original recovery image to FS v1.08.01 FS 90xEU Mar 23 2010
- remove not used bootargs with set default bootargs
- add if port < 1024, abort upload and restart upload again (to get a higher port number)
- add fix for crc-check fault, forse Tftp packages size to 512. ( this is default for the uboot when packes size is not acknowledged)


Note: Use the forse Tftp packages size to 512 when you get the "CRC check Failed" message.



V2.8

- hide non used bootargs

V2.7

- add Maxi U-boot Rev1.0 for AT7000

V2.6

- add Maxi U-boot Rev0.8 for AT7000 (needed for original FW 097)
- update original recovery image to FS v1.07.97 FS 90xEU Mar 09 2010
- add wait time after usb reset

V2.5a

- add read current reseller-id
- update ART for 700 (same as ART 7000)

V2.5

- add change reseller-id
- change original recovery image back to FS v1.07.89 FS 90xEU Feb 3 2010
- update original recovery image to FS v1.07.94 FS 90xEU Feb 26 2010

V2.4a

- fix for crc failed when maxiuboot installed (first try AT7000)

V2.4

- add new Maxi U-boot Rev 0.7 with dimming Display (AT700)


V2.3

- fix bug with empty lines in custombootargs.txt

V2.2

- add load recovery image, Maxi Uboot, Original Uboot from USB devices
- add save bootargs to disk
- add custom bootargs file (use your own bootargs as default)
- add custom bootargs editor
- add "S-USB1", "S-USB2", etc... selection as boot device.


format a USB-Stick as fat32, copy the needed file from ART path to USB=Stick.
Then put your stick in the front USB-Port. (remove all other USB-devices)

The custom bootargs file must be created by the user.
It must be stored in the same dir as ART.
The file name = custombootargs.txt.
Use only one line for each bootarg !!!

Before you can use it you can created it.
There are 3 way's to do this.

1. create the file by hand and store it in the ART dir.
2. connected ART to your box and save the current bootargs as custombootargs.txt in the ART path.
3. press the "Edit Custom" button, this will create a empty file. Copy your settings and save it before exit.

YOU ARE RESPONSIBLE FOR YOUR OWN BOOTARGS SETTINGS !!!

To use the custom bootargs you have to checked the checkbox "Custom".



V2.1

- add Maxi U-boot Rev 0.7
- read Mac-adress from EEPROM ( only when Maxi U-boot installed )

V2.0

- fix bug erasing particial bootloader
- add logging, .../logs/art_log.txt

V1.9

- add Flash Original image (created from cat /dev/mtd7 with original image in flash)

V1.8

- update original recovery image to FS v1.07.89 FS 90xEU Feb 3 2010

V1.7

- fix syntax fault writing bootcmd_3
- remove writing mac address in set defaults
- save comport
- add Boot menu timeout

V1.6

- add select default boot
- add check for wrong IP format

V1.5

- remove all UFS910 entry's

V1.4

- add flash E2 image (only enabled when Maxi U-boot is installed)

V1.3

- again fix bootstop for Original U-boot for AT7000 (change timing)

V1.2

- add Maxi U-boot Rev0.5 for AT7000
- add Recovery, install Original image + erase E2 flash + erase bootsector maxi U-boot for AT7000

V1.1

- add read current settings from box (view ip, serverip, mac, ...)
- disable buttons when write ip, serverip, mac, ...

V1.0

- add install Original U-boot 1.1.2 for AT7000
- fix bootstop for Original U-boot for AT7000

V0.9

- add Maxi U-boot Rev0.4 for AT7000
- add timeout for installing maxi/original U-boot for AT7000

V0.8

- add default bootargs for AT7000

V0.7

- add Maxi U-boot Rev0.3 for AT7000


NOTE:

1. you must have installed NetFrameWorks 2.0 or higher.
2. check your firewall for use of the Tftp (port 69 and random data port)
3. for windows Vista or windows 7 you must run it as administrator
4. make sure you have no other Tftp-server running on your pc
5. make sure the files in the AAF Recover Tool dir are accessible (read access)
6. First set the correct IP's and Mac adress !!!
7. after setting the Mac adress (ethaddr) you need to reboot, otherwise the PING doesn't work !!!

Download (http://www.megaupload.com/?d=TNZ0BFXR)

marce
09-05-2010, 11:31
AAF Recovery Tool 3.7b

V3.7b

- Fixed the typo AV7000
- some changes to the hardware detection (only active when Maxi Uboot installed)

marcel
24-05-2010, 21:36
AAF Recovery Tool 3.9 Atevio7000
========================

V3.9
- fix crash when no comports
- update original recovery image to FS v1.08.22 FS 90xEU May 20 2010


V3.7
- add small change to bootstop (2de)
- add new resellers (AV700)


V3.6
- add write all settings to box (button)
- add small change to bootstop (try to connect before serial received)

V3.5
- fix install Maxi Rev1.1/original Uboot with USB-device

V3.4
- update original recovery image to FS v1.08.16 FS 90xEU Apr 30 2010

V3.3
- add uflasherOrg_1.21_2.23 (original Uboot for AV700/AV7000)

V3.2
- add Maxi U-boot Rev1.1 for AT7000/AT700

V3.1b (AT7000)
- add reseller-id for Astro ASR1200 (111)

V3.1a
- add picture of the box (to avoid wrong use)

V3.1
- update original recovery image to FS/HS v1.08.09 FS/HS 95xEU Apr 01 2010
- fix when crc starts with a zero

V3.0
- update original recovery image to FS v1.08.01 FS 90xEU Mar 23 2010
- remove not used bootargs with set default bootargs
- add if port < 1024, abort upload and restart upload again (to get a higher port number)
- add fix for crc-check fault, forse Tftp packages size to 512. ( this is default for the uboot when packes size is not acknowledged)


Note: Use the forse Tftp packages size to 512 when you get the "CRC check Failed" message.

V2.8
- hide non used bootargs

V2.7
- add Maxi U-boot Rev1.0 for AT7000

V2.6
- add Maxi U-boot Rev0.8 for AT7000 (needed for original FW 097)
- update original recovery image to FS v1.07.97 FS 90xEU Mar 09 2010
- add wait time after usb reset

V2.5a
- add read current reseller-id
- update ART for 700 (same as ART 7000)

V2.5
- add change reseller-id
- change original recovery image back to FS v1.07.89 FS 90xEU Feb 3 2010
- update original recovery image to FS v1.07.94 FS 90xEU Feb 26 2010

V2.4a
- fix for crc failed when maxiuboot installed (first try AT7000)

V2.4
- add new Maxi U-boot Rev 0.7 with dimming Display (AT700)


V2.3
- fix bug with empty lines in custombootargs.txt

V2.2
- add load recovery image, Maxi Uboot, Original Uboot from USB devices
- add save bootargs to disk
- add custom bootargs file (use your own bootargs as default)
- add custom bootargs editor
- add "S-USB1", "S-USB2", etc... selection as boot device.


format a USB-Stick as fat32, copy the needed file from ART path to USB=Stick.
Then put your stick in the front USB-Port. (remove all other USB-devices)

The custom bootargs file must be created by the user.
It must be stored in the same dir as ART.
The file name = custombootargs.txt.
Use only one line for each bootarg !!!

Before you can use it you can created it.
There are 3 way's to do this.

1. create the file by hand and store it in the ART dir.
2. connected ART to your box and save the current bootargs as custombootargs.txt in the ART path.
3. press the "Edit Custom" button, this will create a empty file. Copy your settings and save it before exit.

YOU ARE RESPONSIBLE FOR YOUR OWN BOOTARGS SETTINGS !!!

To use the custom bootargs you have to checked the checkbox "Custom".

V2.1
- add Maxi U-boot Rev 0.7
- read Mac-adress from EEPROM ( only when Maxi U-boot installed )

V2.0
- fix bug erasing particial bootloader
- add logging, .../logs/art_log.txt

V1.9
- add Flash Original image (created from cat /dev/mtd7 with original image in flash)

V1.8
- update original recovery image to FS v1.07.89 FS 90xEU Feb 3 2010

V1.7
- fix syntax fault writing bootcmd_3
- remove writing mac address in set defaults
- save comport
- add Boot menu timeout

V1.6
- add select default boot
- add check for wrong IP format

V1.5
- remove all UFS910 entry's

V1.4
- add flash E2 image (only enabled when Maxi U-boot is installed)

V1.3
- again fix bootstop for Original U-boot for AT7000 (change timing)

V1.2
- add Maxi U-boot Rev0.5 for AT7000
- add Recovery, install Original image + erase E2 flash + erase bootsector maxi U-boot for AT7000

V1.1
- add read current settings from box (view ip, serverip, mac, ...)
- disable buttons when write ip, serverip, mac, ...

V1.0
- add install Original U-boot 1.1.2 for AT7000
- fix bootstop for Original U-boot for AT7000

V0.9
- add Maxi U-boot Rev0.4 for AT7000
- add timeout for installing maxi/original U-boot for AT7000

V0.8
- add default bootargs for AT7000

V0.7
- add Maxi U-boot Rev0.3 for AT7000



NOTE:

1. you must have installed NetFrameWorks 2.0 or higher.
2. check your firewall for use of the Tftp (port 69 and random data port)
3. for windows Vista or windows 7 you must run it as administrator
4. make sure you have no other Tftp-server running on your pc
5. make sure the files in the AAF Recover Tool dir are accessible (read access)
6. First set the correct IP's and Mac adress !!!
7. after setting the Mac adress (ethaddr) you need to reboot, otherwise the PING doesn't work !!!


Ein Super Programm
danke an Black_64, SoLaLa, FSC830
und alle Betatester


Download (http://www.megaupload.com/?d=THMUQXP0)

marcel
24-05-2010, 21:39
AAF Recovery Tool 3.9 Atevio700
========================

V3.9
- fix crash when no comports
- update original recovery image to FS v1.08.22 FS 90xEU May 20 2010


V3.7
- add small change to bootstop (2de)
- add new resellers (AV700)


V3.6
- add write all settings to box (button)
- add small change to bootstop (try to connect before serial received)

V3.5
- fix install Maxi Rev1.1/original Uboot with USB-device

V3.4
- update original recovery image to FS v1.08.16 FS 90xEU Apr 30 2010

V3.3
- add uflasherOrg_1.21_2.23 (original Uboot for AV700/AV7000)

V3.2
- add Maxi U-boot Rev1.1 for AT7000/AT700

V3.1b (AT7000)
- add reseller-id for Astro ASR1200 (111)

V3.1a
- add picture of the box (to avoid wrong use)

V3.1
- update original recovery image to FS/HS v1.08.09 FS/HS 95xEU Apr 01 2010
- fix when crc starts with a zero

V3.0
- update original recovery image to FS v1.08.01 FS 90xEU Mar 23 2010
- remove not used bootargs with set default bootargs
- add if port < 1024, abort upload and restart upload again (to get a higher port number)
- add fix for crc-check fault, forse Tftp packages size to 512. ( this is default for the uboot when packes size is not acknowledged)


Note: Use the forse Tftp packages size to 512 when you get the "CRC check Failed" message.

V2.8
- hide non used bootargs

V2.7
- add Maxi U-boot Rev1.0 for AT7000

V2.6
- add Maxi U-boot Rev0.8 for AT7000 (needed for original FW 097)
- update original recovery image to FS v1.07.97 FS 90xEU Mar 09 2010
- add wait time after usb reset

V2.5a
- add read current reseller-id
- update ART for 700 (same as ART 7000)

V2.5
- add change reseller-id
- change original recovery image back to FS v1.07.89 FS 90xEU Feb 3 2010
- update original recovery image to FS v1.07.94 FS 90xEU Feb 26 2010

V2.4a
- fix for crc failed when maxiuboot installed (first try AT7000)

V2.4
- add new Maxi U-boot Rev 0.7 with dimming Display (AT700)


V2.3
- fix bug with empty lines in custombootargs.txt

V2.2
- add load recovery image, Maxi Uboot, Original Uboot from USB devices
- add save bootargs to disk
- add custom bootargs file (use your own bootargs as default)
- add custom bootargs editor
- add "S-USB1", "S-USB2", etc... selection as boot device.


format a USB-Stick as fat32, copy the needed file from ART path to USB=Stick.
Then put your stick in the front USB-Port. (remove all other USB-devices)

The custom bootargs file must be created by the user.
It must be stored in the same dir as ART.
The file name = custombootargs.txt.
Use only one line for each bootarg !!!

Before you can use it you can created it.
There are 3 way's to do this.

1. create the file by hand and store it in the ART dir.
2. connected ART to your box and save the current bootargs as custombootargs.txt in the ART path.
3. press the "Edit Custom" button, this will create a empty file. Copy your settings and save it before exit.

YOU ARE RESPONSIBLE FOR YOUR OWN BOOTARGS SETTINGS !!!

To use the custom bootargs you have to checked the checkbox "Custom".

V2.1
- add Maxi U-boot Rev 0.7
- read Mac-adress from EEPROM ( only when Maxi U-boot installed )

V2.0
- fix bug erasing particial bootloader
- add logging, .../logs/art_log.txt

V1.9
- add Flash Original image (created from cat /dev/mtd7 with original image in flash)

V1.8
- update original recovery image to FS v1.07.89 FS 90xEU Feb 3 2010

V1.7
- fix syntax fault writing bootcmd_3
- remove writing mac address in set defaults
- save comport
- add Boot menu timeout

V1.6
- add select default boot
- add check for wrong IP format

V1.5
- remove all UFS910 entry's

V1.4
- add flash E2 image (only enabled when Maxi U-boot is installed)

V1.3
- again fix bootstop for Original U-boot for AT7000 (change timing)

V1.2
- add Maxi U-boot Rev0.5 for AT7000
- add Recovery, install Original image + erase E2 flash + erase bootsector maxi U-boot for AT7000

V1.1
- add read current settings from box (view ip, serverip, mac, ...)
- disable buttons when write ip, serverip, mac, ...

V1.0
- add install Original U-boot 1.1.2 for AT7000
- fix bootstop for Original U-boot for AT7000

V0.9
- add Maxi U-boot Rev0.4 for AT7000
- add timeout for installing maxi/original U-boot for AT7000

V0.8
- add default bootargs for AT7000

V0.7
- add Maxi U-boot Rev0.3 for AT7000



NOTE:

1. you must have installed NetFrameWorks 2.0 or higher.
2. check your firewall for use of the Tftp (port 69 and random data port)
3. for windows Vista or windows 7 you must run it as administrator
4. make sure you have no other Tftp-server running on your pc
5. make sure the files in the AAF Recover Tool dir are accessible (read access)
6. First set the correct IP's and Mac adress !!!
7. after setting the Mac adress (ethaddr) you need to reboot, otherwise the PING doesn't work !!!


Ein Super Programm
danke an Black_64, SoLaLa, FSC830
und alle Betatester

Download (http://www.megaupload.com/?d=J6RILUBK)

marcel
24-08-2010, 21:38
AAF Recovery Tool
=============

V4.0

- update original recovery image to FS v1.08.34 FS 9000 Jul 29 2010

- fix set bootdefault


Download (http://www.megaupload.com/?d=H8TWK4BO)

marcel
24-08-2010, 21:43
AAF Recovery Tool
=============

V4.0

- update original recovery image to FS v1.08.34 FS 9000 Jul 29 2010

- fix set bootdefault


Download (http://www.megaupload.com/?d=78MN72BP)

marcel
25-09-2010, 22:21
AAF Recovery Tool 7000 Version 4.2
=========================

V4.2

- update original recovery image to FS v1.08.44 HS 9500 Sep 19 2010


V4.1

- update original recovery image to FS v1.08.37 FS 9000 Aug 25

2010

Download (http://www.megaupload.com/?d=WMTG66ZP)

marcel
25-09-2010, 22:25
AF Recovery Tool 700 Version 4.2
=========================

V4.2

- update original recovery image to FS v1.08.44 HS 9510A Sep 19 2010
- add reseller-id X-Cruiser 400 HD
- add reseller-id forGalaxy Innovations Gi S8290 HD


Download (http://www.megaupload.com/?d=JJJRAEKM)

marce
17-12-2010, 09:33
AAF Recovery Tool 700 Version 4.4


V4.4

- update original recovery image to FS v1.08.65 FS 9000 Dec 03 2010

Danke an Black_64 und alle Betatester.


Tool 700 Version 4.4 (http://upload4.net/download.php?uid=CQZZH9JJ)

marce
17-12-2010, 09:34
AAF Recovery Tool 7000 Version 4.4


V4.4

- update original recovery image to FS v1.08.65 FS 9000 Dec 03 2010

Danke an Black_64 und alle Betatester.


Tool 7000 Version 4.4 (http://upload4.net/download.php?uid=0NO7JAZE)

marce
22-01-2011, 09:55
AAF Recovery Tool 700x Version


20-01-11 V4.5

- update original recovery image to FS V1.08.75 FS 9000 Jan 03 2011
- add flash E2 with USB device (filename on USB must be "e2flash_7000.img")





Version 4.5 Atevio7000 (http://www.multiupload.com/4KPK7FCRR9)


Version 4.5 Atevio700 (http://www.multiupload.com/ZT5TRM405I)

hilton
26-06-2011, 10:49
AAF Recovery Tool AV7500
===================

V2.0

- delete bootargs when installing original uboot

Bas19801
17-09-2013, 11:51
they don't work @ me rebox 2200hd pvr

EZ Archive Ads Plugin for vBulletin Copyright 2006 Computer Help Forum